View 10XSD200_7695474.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

document number: mc10XSD200 rev. 2.0, 9/2013 freescale semiconductor ? advance information * this document contains certain information on a new product. ? specifications and information herein are subject to change without notice. ? freescale semiconductor, in c., 2013. all rights reserved. dual 10 mohm high side switch the 10XSD200 device is part of a 36 v dual high side switch product family with integrated co ntrol, and a high number of protective and diagnostic functions. it has been designed for industrial applications. the low r ds(on) channels (<10 m ? ) can control different load types; bulbs, solenoids, or dc motors. control, device configuration, and diagnostics are performed through a 16- bit serial peripheral interface (spi), allowing easy integration into existing applications. this device is powered by smartmos technology. both channels can be controlled individually by external or internal clock signals, or by direct inputs. using the internal clock allows fully autonomous device operation. progr ammable output voltage slew- rates (individually programmable) helps improve electromagnetic compatability (emc) performance. to avoid shutting off the device upon inrush current, while still being able to closely track the load current, a dynamic overcurrent thres hold profile is featured. switching current of each channel can be sensed with a programmable sensing ratio. whenever communication with the external microcontroller is lost, the device enters a fail-s afe operation mode, but remains operational, controllable, and protected. features ? normal operating range: 8.0 - 36 v, extended range: 6.0 - 58 v ? two fully protected 10 m ? (@ 25 c) high side switches ?up to 6.0 a steady state current per channel ? separate bulb and dc motor latched overcurrent handling ? individually programmable internal/external pwm clock signals ? overcurrent, short-circuit, and overtemperature protection with programmable autoretry functions ? accurate temperature and current sensing ? openload detection (channel in off and on state), also for led applications (7.0 ma typ.) ?3.3 v and 5.0 v compatible 16-bit spi port for device control, ? configuration and diagnostics at rates up to 8.0 mhz figure 1. simplified application diagram fk suffix (pb-free) 98asa00428d 23 pin pqfn (12 x12 mm) 10XSD200 ordering information device temperature range (t a ) package mc10XSD200fk - 40 to 125 c 23 pqfn high side switch mcu v dd clock fsb sclk csb so rstb si in0 in1 csns gnd vdd vpwr hs0 hs1 load i/o sclk csb si i/o so i/o i/o a/d gnd load m conf0 conf1 fsob i/o a/d sync i/o 10XSD200 v dd v pwr free datasheet http:///
analog integrated circuit device data ? 2 freescale semiconductor 10XSD200 internal block diagram internal block diagram figure 2. internal block diagram gnd overtemperature detect. control severe short-circuit selectable overcurrent internal regulator selectable slew rate gate driver over/undervoltage protections hs0 vpwr vdd csb sclk so si rstb clock fsb in0 hs1 hs0 hs1 in1 detection output csns i dwn i up openload detect detection temperature feedback v reg short-circuit to charge v dd failure detection calibratable oscillator * pwm module drain/gate clamp r dwn current sense analog mux overtemperature prewarning pump por fsob conf0 conf1 i up v reg i dwn sync i dwn vpwr detec. logic * *blocks marked in grey have implemented independently for each of both channels free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 3 10XSD200 table of contents table of contents internal block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 static electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 timing diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 pin assignment and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 functional internal block description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 functional device operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 operation and operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 protection and diagnostic features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 logic commands and spi registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 soldering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 free datasheet http:///
analog integrated circuit device data ? 4 freescale semiconductor 10XSD200 pin assignment pin assignment figure 3. 10XSD200 pin assignments table 1. 10XSD200 pin description the function of each pin is described in the section functional description pin number pin name function formal name definition 1 csns output output current/ temperature monitoring this pin either outputs a current proportional to the channel?s output current or a voltage proportional to the temperature of the gnd pin (pin 14). selection between current and temperature sensing, as well as setting the current sensing sensitivity, are performed through the spi interface. an external pull- down resistor must be connected between csns and gnd. 2 3 in0 in1 input direct inputs the in[0 : 1] input pins are used to directly control the switching state of both switches and consequently the voltage on the hs0 : hs1 output pins. the pins are connected to gnd by internal pull-down resistors 4 fsob output fail-safe output (active low) fsob is asserted (active-low) upon entering fail-safe mode (see functional description ) this open-drain output requires an external pull-up resistor to vpwr 5 6 conf0 conf1 input configuration input the conf[0 : 1] input pins are used to select the appropriate overcurrent detection profile (bulb /dc motor) for each of both channels. conf requires a pull-down resistor to gnd. 7 fsb output fault status (active low) this open-drain output pin (external pull-up resistor to vdd is required) is set when the device enters fault mode (see fault mode ) 8 clock input pwm clock the clock input gives the time-base wh en the device is operated in external clock/internal pwm mode. this pin has an internal pull-down current source. 9 rstb input reset this input pin is used to initialize the dev ice?s configuration - and fault registers. reset puts the device in sleep mode (low current consumption) provided it is not stimulated by direct input signals. this pin is connected to gnd by an internal pull-down resistor. 10 csb input chip select (active low) this input pin is connected to the spi chip-select output of an external micro- controller. csb is internally pulled up to v dd by a current source i up . transparent top view 1 12 10 9 8 7 6 5 4 3 2 20 19 15 14 13 hs0 hs1 csns in1 fsob conf0 conf1 fsb rstb csb sclk si vdd gnd vpwr 11 23 22 21 16 17 18 clock in0 sync gnd vpwr so gnd vpwr free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 5 10XSD200 pin assignment 11 sclk input serial clock this input pin is to be connected to an external spi clock signal. the sclk pin is internally connected to a pull-down current source i dwn 12 si input serial input this input pin receives the spi input data from an external device (micro- controller or another extreme switch dev ice in case of daisy-chaining). the si pin is internally connected to a pull-down current source i dwn 13 vdd power digital drain voltage this is the positive supply pin of the spi interface. 16 so output serial output this output pin transmits spi data to an external device (external micro- controller or the si pin of the next sp i device in case of daisy-chaining). the pin doesn?t require external pull-up or pul l-down resistors, but a series resistor is recommended to limit current consum ption in case of gnd disconnection 14, 17, 22 gnd ground ground these pins, internally connected, are the ground pins for the logic and analog circuitry. it is recommended to al so connect these pins on the pcb. 15,18,21 vpwr power positive power supply these pins, internally connected, s upply both the device?s power and control circuitry (except the spi port). the drain of both internal mosfet switches is connected to them. pin 15 is the device?s primary thermal pad. 19 20 hs1 hs0 output power switch outputs output pins of the switches, to be connected to the load. 23 sync output output current monitoring synchronization this output pin is asserted (logic lo w) when the current sense (cs) output signal is within the specif ied accuracy range. readi ng the sync pin allows the external microprocessor to synchroni ze to the device when operating in autonomous operating mode. sync is open-drain and requires a pull-up resistor to vdd. table 1. 10XSD200 pin description (continued) the function of each pin is described in the section functional description pin number pin name function formal name definition free datasheet http:///
analog integrated circuit device data ? 6 freescale semiconductor 10XSD200 electrical characteristics maximum ratings electrical characteristics maximum ratings table 2. maximum ratings all voltages are relative to ground unless mentioned othe rwise. exceeding these ratings may cause permanent damage. parameter symbol maximum ratings unit electrical ratings vpwr supply voltage range voltage transient at 25 c (500 ms) reverse voltage at 25 c fast negative transient pulses (iso 7637-2 pulse #1, v pwr =14 v & r i =10 ? ) v pwr 58 -28 -60 v vdd supply voltage range v dd -0.3 to 5.5 v voltage on input pins (6) (except in[0:1]) and output pins (7) (except hs[0:1]) v max,logic (6) -0.3 to 5.5 v voltage on fail-safe output (fsob) v fso -0.3 to 58 v voltage on so pin v so -0.3 to v dd +0.3 v voltage (continuous, max. allowable) on in[0:1] inputs v in,max 58 v voltage (continuous, max. allowable) on output pins (hs [0:1]), v hs[0:1] -28 to 58 v rated continuous output current per channel (1) i hs[0:1] 6.0 a maximum allowable energy dissipation per channel and two parallel channels, single-pulse method (2) e cl [0:1]_sing 300 mj maximum allowable energy dissipation per channel and two parallel channels, repetitive-pulses condition. 1 (3) e cl [0:1]_rep1 220 mj maximum allowable energy dissipation per channel and two parallel channels, repetitive-pulses condition. 2 (4) e cl [0:1]_rep2 220 mj esd voltage (5) human body model (hbm) for hs[0:1], vpwr and gnd human body model (hbm) for other pins charge device model (cdm) package corner pins (1, 13, 19, 20) all other pins v esd1 v esd2 v esd3 v esd4 8000 2000 750 500 v notes: 1. output current rating valid as long as maximum junction temperature is not exceeded. for computation of the maximum allowable output current, the thermal resistance of the package & t he underlying heatsink must be taken into account 2. single pulse energy dissipation, single-puls e short-circuit method (l l = 2.0 mh, r = 30 m ?? v pwr = 28 v, t j = 150 ? c initial). 3. dissipation during repetitive cycles : switch off upon short-circuit (l l = 20 h, r = 200 m ??? v pwr = 28 v, t j = 125 ? c initial, f s <2.0 hz). 4. dissipation during repetitive cycles: switch off upon short-circuit (l l = 40 h, r = 400 m ??? v pwr = 28 v, t j = 125 ? c initial, f s <2.0 hz). 5. esd testing is performed in accordance with the human body model (hbm) (c zap = 100 pf, r zap = 1500 ? ), and the charge device model (cdm), robotic (c zap = 4.0 pf). 6. concerned input pins are: conf[0:1], rstb, si, sclk, clock, and csb. 7. concerned output pins are: csns, sync, and fsb. free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 7 10XSD200 electrical ch aracteristics maximum ratings thermal ratings operating temperature (8) ambient junction t a t j - 40 to 125 - 40 to 150 ? c storage temperature t stg - 55 to 150 ? c thermal resistance junction to case bottom/ vpwr flag surface r ? jc 0.22 ? c/ w peak package reflow temperature during reflow (9) , (10) t pprt note 10 ? c notes: 8. to achieve high reliability over 10 y ears of continuous operation, the device's conti nuous operating junction temperature sho uld not exceed 125 c. 9. pin soldering temperature limit is for 40 seconds maximum duration. not designed for immersion soldering. exceeding these lim its may cause malfunction or permanent damage to the device. 10. freescale?s package reflow capability m eets pb-free requirements for jedec standard j-std-020. for peak package reflow temperature and moisture sensitivity levels (msl), go to www.free scale.com, search by part number [e.g. remove prefixes/suffixe s and enter the core id to view all orderable parts. (i.e. mc33xxxd enter 33xxx), and review parametrics. table 2. maximum ratings (continued) all voltages are relative to ground unless mentioned othe rwise. exceeding these ratings may cause permanent damage. parameter symbol maximum ratings unit free datasheet http:///
analog integrated circuit device data ? 8 freescale semiconductor 10XSD200 electrical characteristics static electrical characteristics static electrical characteristics table 3. static electric al characteristics unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c, v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit supply electrical characteristics supply voltage range: full specification compliant extended mode (11) v pwr 8.0 6.0 ? ? 36 58 v v pwr supply current, device in wake-up mode, channel on, openload outputs in on-state, hs[0 : 1] open, in[0:1] > v ih i pwr(on) ? 6.5 8.0 ma v pwr supply current, device in wake-up mode (standby), channel off openload in off-state detection disabled, hs[0 : 1] shorted to ground with v dd = 5.5 v and rstb > v wake i pwr(sby) ? 6.5 8.0 ma sleep state supply current v pwr = 24 v, rstb = in[0:1] < v wake , hs[0 : 1] connected to ground t a = 25 c t a = 125 c i pwr(sleep) ? ? 3.0 ? 10.0 60.0 ? a v dd supply voltage v dd(on) 3.0 ? 5.5 v v dd supply current at v dd = 5.5 v no spi communication 8.0 mhz spi communication (12) i dd(on) ? ? ? 5.0 2.2 ? ma v dd sleep state current at v dd = 5.5 v with or without v pwr i dd(sleep) ? ? 5.0 ? a overvoltage shutdown threshold v pwr(ov) 39 42 45.5 v overvoltage shutdown hysteresis v pwr(ovhys) 0.2 0.8 1.5 v undervoltage shutdown threshold (13) v pwr(uv) 5.0 ? 6.0 v v pwr power-on-reset (por) voltage threshold (13) v pwr(por) 2.2 2.6 4.0 v v dd power-on-reset (por) voltage threshold (13) v dd(por) 1.5 2.0 2.5 v v dd supply failure voltage threshold (assumed v pwr > v pwr(uv) ) v dd(fail) 2.2 2.5 2.8 v notes 11. in extended mode, several device functions (channel control, r ds(on) and overtemperature protection) are guaranteed, but compliance with the specified values in this document is not. below 6.0 v, the device is only protected from overheating (thermal shutdown). above v pwr(ov) , the channels can only be turned on when the overvoltage detection function has been disabled. 12. typical value guaranteed per design. 13. when the device recovers from undervoltage and returns to normal mode (6.0 v < v pwr < 58 v) before the end of the auto-retry period (see auto-retry ), the device performs normally. when v pwr drops below v pwr(uv) , undervoltage is detected see undervoltage fault (latchable fault) and emc performances . free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 9 10XSD200 electrical ch aracteristics static electrical characteristics electrical characteristics of the output stage (hs0 and hs1) on-resistance, drain-to-source ( i hs = 3.0 a, t j = 25 c) csns_ratio = 0 v pwr = 8.0 v v pwr = 28 v v pwr = 36 v r ds(on)25 ? ? ? ? ? ? 10 10 10 m ? on-resistance, drain-to-source (i hs = 3.0 a,t j = 150 c) csns_ratio = 0 v pwr = 8.0 v v pwr = 28 v v pwr = 36 v r ds(on)150 ? ? ? ? ? ? 18 18 18 m ? on-resistance, drain-to-source difference from one channel to the other in parallel mode (i hs = 1.0 a,t j = 150 c) csns_ratio = x ? r ds(on)150 -0.8 ? +0.8 m ? on-resistance, source-drain (i hs = -3.0 a, t j = 150 c, ? v pwr = -24 v) r sd(on)150 ? ? 18 m ? max. detectable wiring length (2.5 mm2) for severe short-circuit detection high slew rate selected medium slew rate selected: low slew rate selected: l short 20 50 100 85 160 280 140 300 600 cm overcurrent detection thresholds with csns_ratio bit = 0 (csr0) och1_0 och2_0 ocm1_0 ocm2_0 ocl1_0 ocl2_0 ocl3_0 55 35 22 13 9.0 6.0 3.0 66 42 26 16 10.8 7.2 3.6 77 49 31 19.5 12.6 8.4 4.2 a overcurrent detection thresholds with csns_ratio bit = 1(csr1) och1_1 och2_1 ocm1_1 ocm2_1 ocl1_1 ocl2_1 ocl3_1 18.3 11.7 7.2 4.4 3.0 2.0 0.96 22 14.0 8.7 5.3 3.6 2.4 1.2 26.5 16.3 10.1 6.2 4.2 2.8 1.44 a output pin leakage current in sleep state (positive value = outgoing) v hs,off = 0 v (v hs,off = output voltage in off state) v hs,off = v pwr , device in sleep state (v pwr = 24 v) i out_leak ? -40.0 ? ? +11 +5.0 a switch turn-on threshold for supply overvoltage (v pwr -gnd) v d_gnd(clamp) 58 ? 66 v switch turn-on threshold for drai n-source overvoltage (measured at i out = 500 ma v ds(clamp) 58 ? 66 v table 3. static electrical characteristics (continued) unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c, v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit free datasheet http:///
analog integrated circuit device data ? 10 freescale semiconductor 10XSD200 electrical characteristics static electrical characteristics electrical characteristics of the output stage (hs0 and hs1) (continued) current sensing ratio (14) csns_ratio bit = 0 (high current mode) csns_ratio bit = 1 (low current mode) c sr0 c sr1 ? ? 1/3000 1/1000 ? ? ? minimum measurable load current with compensated error (15) i _load_min ? ? 100 ma csns leakage current in off state ( csnsx_en = 0, csns_ratio bit_x = 0 ) i csr_leak -4.0 ? +4.0 a systematic offset error (see current sense errors ) i _load_err_sys ? 11 ? ma random offset error i _load_err_rand -150 ? 150 ma e sr0 output current sensing error (%, uncompensated (16) at output current level (sense ratio c sr0 selected): t j =-40 ? c 6.0 a 3.0 a 1.5 a 0.75 a t j =125 ? ? c 6.0 a 3.0 a 1.5 a 0.75 a t j =25 to 125 ? ? c 6.0 a 3.0 a 1.5 a 0.75 a e sr0_err -13 -12 -17 -31 -10 -9.0 -12 -19 -10 -9.0 -12 -22 ? ? ? ? ? ? ? ? ? ? ? ? 13 12 17 31 10 9.0 12 19 10 9.0 12 22 % notes: 14. current sense ratio c srx = i csns / i hs[x] 15. see note (16) , but with i csns_meas obtained after compensation of i _load_err_rand (see activation and use of offset compensation ). further accuracy improvements can be obtained by performing a 1 or 2 point calibration. 16. e srx_err =(i csns_meas / i csns_model ) -1, with i csns_model = (i(hs[x])+ i _load_err_sys ) * c srx , (i _load_err_sys defined above, see section current sense error model ). with this model, load current becomes: i(hs[x]) = i csns / c srx - i _load_err_sys table 3. static electrical characteristics (continued) unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c, v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 11 10XSD200 electrical ch aracteristics static electrical characteristics e sr0 output current sensing error (% after offset compensation (17) at output current level (sense ratio c sr0 selected): t j =-40 ? c 6.0 a 3.0 a 1.5 a 0.75 a t j =125 ? ? c 6.0 a 3.0 a 1.5 a 0.75 a t j =25 to 125 ? ? c 6.0 a 3.0 a 1.5 a 0.75 a e sr0_err (comp) -10 -10 -10 -10 -9.0 -8.0 -8.0 -9.0 -9.0 -8.0 -8.0 -9.0 ? ? ? ? ? ? ? ? ? ? ? ? 10 10 10 10 9.0 8.0 8.0 9.0 9.0 8.0 8.0 9.0 % e sr1 output current sensing error (%, uncompensated (18) at output current level (sense ratio c sr1 selected): t j =-40 ? c 1.5 a t j =125 ? ? c 1.5 a t j =25 to 125 ? ? c 1.5 a e sr1_err -15 -12 -12 ? ? ? 15 12 12 % notes: 17. see note (16) , but with i csns_meas obtained after compensation of i _load_err_rand (see activation and use of offset compensation ). further accuracy improvements can be obtained by performing a 1 or 2 point calibration. 18. e srx_err =(i csns_meas / i csns_model ) -1, with i csns_model = (i(hs[x])+ i _load_err_sys ) * c srx , (i _load_err_sys defined above, see section current sense error model ). with this model, load current becomes: i(hs[x]) = i csns / c srx - i _load_err_sys table 3. static electrical characteristics (continued) unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c, v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit free datasheet http:///
analog integrated circuit device data ? 12 freescale semiconductor 10XSD200 electrical characteristics static electrical characteristics electrical characteristics of the output stage (hs0 and hs1) (continued) e sr1 output current sensing error (% (level) after offset compensation (19) at output current level (sense ratio c sr1 selected): t j =-40 ? c 1.5 a 0.5 a 0.25 a 0.15 a t j =125 ? ? c 1.5 a 0.5 a 0.25 a 0.15 a t j =25 to 125 ? ? c 1.5 a 0.5 a 0.25 a 0.15 a e sr1_err (comp) -10 -11 -18 -29 -8.0 -10 -12 -16 -8.0 -10 -13 -21 ? ? ? ? ? ? ? ? ? ? ? ? 10 11 18 29 8.0 10 12 16 8.0 10 13 21 % e sr0 output current sensing error in parallel mode (%, uncompensated (20) ) at outputs current level (sense ratio c sr0 selected): t j =-40 ? c 6.0 a (per channel) 3.0 a (per channel) t j =125 ? ? c 6.0 a (per channel) 3.0 a (per channel) t j =25 to 125 ? ? c 6.0 a (per channel) 3.0 a (per channel) e sr0_err_par -10 -11 -8.0 -8.0 -8.0 -8.0 ? ? ? ? ? ? 10 11 8.0 8.0 8.0 8.0 % notes: 19. see note (20) , but with i csns_meas obtained after compensation of i _load_err_rand (see activation and use of offset compensation ). further accuracy improvements can be obtained by performing a 1 or 2 point calibration. 20. e srx_err =(i csns_meas / i csns_model ) -1, with i csns_model = (i(hs[x])+ i _load_err_sys ) * c srx , (i _load_err_sys defined above, see section current sense error model ). with this model, load current becomes: i(hs[x]) = i csns / c srx - i _load_err_sys table 3. static electrical characteristics (continued) unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c, v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 13 10XSD200 electrical ch aracteristics static electrical characteristics electrical characteristics of the output stage (hs0 and hs1) (continued) current sense clamping voltage (condition: r(csns) > 10 kohm) v cl(csns) 5.5 ? 7.5 v openload detection current threshold in off state (21) i old(off) 30 ? 100 ? a openload fault detection voltage threshold (21) v old(thres) 4.0 ? 5.5 v openload detection current threshold in on state (see openload detection in on state (ol_on) ): csns_ratio bit = 0 csns_ratio bit = 1 (fast slew rate sr[1:0] = 10 mandatory for this function) i old(on) 80 5.0 300 7.0 600 10 ma time period of the periodically activated openload in on state detection for csns_ratio bit = 1 t olled 105 150 195 ms output shorted-to-v pwr detection voltage threshold (channel in off state) v osd(thres) v pwr -1.2 v pwr -0.8 v pwr -0.4 v switch turn-on threshold for negative output voltages (protects against negative transients) - (measured at i out = 100 ma, channel in off state) v cl -35 ? -24 v switch turn-on threshold for negative output voltages difference from one channel to the other in parallel mode - (measured at i out = 100 ma, channel in off state) ? v cl -2.0 ? +2.0 v switching state (on/off) discrimination thresholds v hs_th 0.45*v pwr 0.5*v pwr 0.55*v pwr v shutdown temperature (power mosfet junction; 6.0 v < v pwr < 58 v) t sd 160 175 190 ? c electrical characteristics of the control interface pins logic input voltage, high (22) v ih 2.0 ? 5.5 v logic input voltage, low (22) v il -0.3 ? 0.8 v wake-up threshold voltage (in[0:1] and rstb) (23) v wake 1.0 ? 2.2 v internal pull-down current source (on inputs: clock, sclk and si) (24) i dwn 5.0 ? 20 ? a internal pull-up current source (input csb) (25) i up_csb 5.0 ? 20 ? a internal pull-up current source (input conf[0:1]) (26) i up_conf 25 ? 100 ? a capacitance of so, fsb and fsob pins in tri-state c so ? ? 20 pf internal pull-down resistance (rstb and in[0:1]) r dwn 125 250 500 k ? input capacitance (27) c in ? 4.0 12 pf notes: 21. minimum required value of openload impedance for detection of openload in off-state: 200 k ? .(v old(thres) = v hs @ i old(off) ) 22. high and low voltage ranges apply to si, csb, sclk, rstb, in [0:1] and clock input signals. the in[0:1] signals may be derive d from v pwr and can tolerate voltages up to 58 v. 23. voltage above which the device wakes up 24. pull-down current-value for v si > 0.8 v and v sclk > 0.8 v and v clock > 0.8 v. 25. pull-up current-value for v csb < 2.0 v. csb has an internal pull-up current source connected to v dd . 26. pins conf[0:1] are connected to an internal current s ource, connected itself to an internal voltage regulator (v reg ~ 3.0 v). 27. input capacitance of si, csb, sclk, rstb, in[0:1], conf[0:1 ], and clock pins. this parameter is guaranteed by the manufactur ing process but is not tested in production. table 3. static electrical characteristics (continued) unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c, v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit free datasheet http:///
analog integrated circuit device data ? 14 freescale semiconductor 10XSD200 electrical characteristics static electrical characteristics electrical characteristics of the control interface pins (continued) so high-state output voltage (i oh = 1.0 ma) v soh v dd -0.4 ? ? v sync, so, fsob and fsb low-state output voltage (i ol = -1.0 ma) v sol ? ? 0.4 v sync, so, csns, fsob and fsb tri-state leakage current: ( 0.0 v < v(so) < v dd , or v(fs) or v(sync) = 5.5 v, or v(fso) = 36 v or v(csns) = 0 v i so(leak) - 2.0 0.0 2.0 ? a conf[0:1] required values of the external pull-down resistor - lighting applications - dc motor applications r conf 1.0 50 ? ? 10 infinite k ? table 3. static electrical characteristics (continued) unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c, v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit free datasheet http:///
analog integrated circuit device data ? 15 freescale semiconductor 10XSD200 electrical characteristics dynamic electrical characteristics dynamic electrical characteristics table 4. dynamic electri cal characteristics unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c,v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit output voltage switching characteristics rising and falling edges medium slew rate (sr[1:0] = 00) (28) v pwr = 16 v v pwr = 28 v v pwr = 36 v sr r_00 sr f_00 0.164 0.28 0.34 ? ? ? 0.65 0.79 0.90 v/ ? s rising and falling edges low slew rate (sr[1:0] = 01) (28) v pwr = 16 v v pwr = 28 v v pwr = 36 v sr r_01 sr f_01 0.081 0.14 0.17 ? ? ? 0.32 0.395 0.45 v/ ? s rising and falling edges high slew rate / sr[1:0] = 10) (28) v pwr = 16 v v pwr = 28 v v pwr = 36 v sr r_10 sr f_10 0.29 0.55 0.68 ? ? ? 1.30 1.58 1.80 v/ ? s rising/falling edge slew rate matching 16 v < v pwr < 36 v sr r /sr f 0.65 1.0 1.35 edge slew rate difference from one channel to the other in parallel mode (28) 16 v < v pwr < 36 v sr[1:0] = 00 sr[1:0] = 01 sr[1:0] = 10 ? sr -0.12 -0.06 -0.2 0.0 0.0 0.0 +0.12 +0.06 +0.2 v/ ? s output turn-on and turn-off delays (medium slew rate: sr[1:0] = 00) (29) 16 v < v pwr < 36 v t dly_00 30 ? 160 ? s output turn-on and turn-off delays (low slew rate / sr[1:0] = 01) (29) 16 v < v pwr < 36 v t dly_01 50 ? 300 ? s output turn-on and turn-off delays (high slew rate / sr[1:0] = 10) (29) 16 v < v pwr < 36 v t dly_10 15 ? 80 ? s turn-on and turn-off delay time matching ( t dly(on) - t dly(off) ) f pwm = 400 hz, 16 v < v pwr < 36 v , duty cycle on in[x] = 50 %, sr[1:0] = 00 ? ? t rf_00 -25 0.0 25 ? s turn-on and turn-off delay time matching ( t dly(on) - t dly(off) ) f pwm = 200 hz, 16 v < v pwr < 36 v , duty cycle on in[x] = 50 %, sr[1:0] = 01 ? ? t rf_01 -90 0.0 90 ? s turn-on and turn-off delay time matching ( t dly(on) - t dly(off) ) f pwm = 1.0 khz, 16 v < v pwr < 36 v , duty cycle on in[x] = 50 %, sr[1:0] = 10 ? ? t rf_10 -13 0.0 13 ? s notes 28. rising and falling edge slew rates specified for a 20 to 80% voltage variation on a 10 ?? resistive load (see figure 4 ). 29. turn-on delay time measured as delay between a rising edge of the channel control signal (in[0 : 1] = 1 or csb) and the associated rising edge of the output voltage up to: v hs[0 : 1] = v pwr / 2 (where r l = 5.0 ? ? ). turn-off delay time is measured as time between a falling edge of the channel control signal (in[0 : 1] = 0 or csb pin) and the associated falling edge of the output voltage up to the instant at which: v hs[0 : 1] = v pwr / 2 (r l = 5.0 ? ) free datasheet http:///
analog integrated circuit device data ? 16 freescale semiconductor 10XSD200 electrical characteristics dynamic electrical characteristics switching characteristics (continued) delay time difference from one channel to the other in parallel mode (30) 16 v < v pwr < 36 v sr[1:0] = 00 sr[1:0] = 01 sr[1:0] = 10 ? ? t (dly) -25 -50 -12 0.0 0.0 0.0 +25 +50 +12 ? s fault detection delay time (31) t fault ? 5.0 8.0 ? s output shutdown delay time (32) t detect ? 7.0 12 ? s current sense output settling time for sr[1:0] = 00 (medium slew rate) ? v pwr = 28 v (33) 16 v < v pwr < 36 v (34) t csnsval_00 ? 0.0 104 ? ? 250 ? s current sense output settling time for sr[1:0] = 01(low slew rate) ? v pwr = 28 v (33) 16 v < v pwr < 36 v (34) t csnsval_01 ? 0.0 167 ? ? 355 ? s current sense output settling time for sr[1:0] = 10 (high slew rate) ? v pwr = 28 v (33) 16 v < v pwr < 36 v (34) t csnsval_10 ? 0.0 76 ? ? 210 ? s sync output signal delay for sr[1:0] = 00 (medium sr) (34) t syncval_00 50 ? 160 ? s sync output signal delay for sr[1:0] = 01 (low sr) (34) t syncval_01 80 ? 320 ? s sync output signal delay for sr[1:0] = 10 (high sr) (34) t syncval_10 22 ? 80 ? s recommended sync_to_read delay sr[1:0] = 00 (medium slew rate) (34) t synread_00 ? ? 200 s recommended sync_to_read delay sr[1:0] = 01 (low slew rate) (34) t synread_01 ? ? 300 s recommended sync_to_read delay sr[1:0] = 10 (high slew rate) (34) t synread_10 ? ? 200 s upper overcurrent threshold duration t och1 t och2 6.0 12.0 8.6 17.2 11.2 22.4 ms medium overcurrent threshold duration (conf = 0; lighting profile) t ocm1_l t ocm2_l 48 96 67 137 87 178 ms medium overcurrent threshold duration (conf = 1; dc motor profile) t ocm1_m t ocm2_m 96 245 137 350 178 455 ms frequency & pwm duty cycle ranges (35) (protections fully operational, see protective functions ) switching frequency range - direct inputs f control 0.0 ? 1000 hz switching frequency range - external clock with internal pwm (recommended) f pwm_ext 20 ? 1000 hz switching frequency range - internal clock with internal pwm (recommended) f pwm_int 60 ? 1000 hz duty cycle range r control 0.0 ? 100 % notes: 30. rising and falling edge slew rates specified for a 20 to 80% voltage variation on a 10 ?? resistive load (see figure 4 ). 31. time required to detect and report the fault to the fsb pin. 32. time required to switch off the channel after detection of over temperature (ot), overcurrent (oc), sc or uv error (time meas ured between start of the negative edge on the fsb pin and the falling edge on the output voltage until v(hs[0:1)) = 50% of v pwr 33. typical value given for a 70 ? resistive load for csns_ratio_s = 1 34. settling time ( = t csnsval_xx ), sync output signal delay ( = t syncval_xx ) and read-out delay ( = t synread_xx ) are defined for a stepped load current using a 10 ? resistive load for csns_ratio_s = 0. (see figure 9 and output current monitoring (csns) ). 35. in direct input mode, the lower frequency limit is 0 hz with rstb=5.0 v and 4.0 hz with rstb=0 v. duty-cycle applies to instants at which v hs = 50% v pwr . for low duty cycle values, the effective value al so depends on the value of the selected slew rate. table 4. dynamic electrical characteristics (continued) unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c,v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 17 10XSD200 electrical ch aracteristics dynamic electrical characteristics availability diagnostic functions o ver duty-cycle and switching frequency (protection & diagnostics both fully operational, see diagnostic features for the exact boundary values) available duty cycle range, f pwm = 1.0 khz high slew rate (notes) ol_off ol_on os r pwm_1k_h 0.0 35 0.0 ? ? ? 62 100 90 % available duty cycle range, f pwm = 400 hz, medium slew rate mode (notes) ol_off ol_on os r pwm_400_m 0.0 21 0.0 ? ? ? 81 100 88 % available duty cycle range, f pwm = 400 hz, high slew rate mode (notes) ol_off ol_on os r pwm_400_h 0.0 14 0.0 ? ? ? 84 100 95 % available duty cycle range, f pwm = 200 hz, low slew rate mode (notes) ol_off ol_on os r pwm_200_l 0.0 15 0.0 ? ? ? 86 100 93 % available duty cycle range, f pwm = 200 hz, medium slew rate mode (notes) ol_off ol_on os r pwm_200_m 0.0 11 0.0 ? ? ? 90 100 94 % available duty cycle range, f pwm = 100 hz in low slew rate mode (notes) ol_off ol_on os r pwm_100_l 0.0 8.0 0.0 ? ? ? 93 100 96 % deviation of the internal clock pwm frequency after calibration (37) a fpwm(cal) -10 ? +10 % default output frequency when using an uncalibrated oscillator f pwm(0) 280 400 520 hz minimal required low time during calibrat ion of the internal clock through csb t csb(min) 1.0 1.5 2.0 ? s maximal allowed low time during calibration of the internal clock through csb t csb(max) 70 100 130 ? s recommended external clock frequency range (external clock/pwm module) f clock 15 ? 512 khz upper detection threshold for exte rnal clock frequency monitoring f clock(max) 512 730 930 khz lower detection threshold for exte rnal clock frequency monitoring f clock(min) 5.0 7.0 10 khz notes: 36. the device can be operated outside the spec ified duty cycle and frequency ranges (basic protective functions oc, sc, uv, ov, and ot remain active), but the availability of the diagnostic functions ol_on, ol_off, and os is affected. ol_off duty-cycle range is guaranteed by design characterization. 37. values guaranteed from 60 hz to 1.0 khz (recommended switching frequency range). table 4. dynamic electrical characteristics (continued) unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c,v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit free datasheet http:///
analog integrated circuit device data ? 18 freescale semiconductor 10XSD200 electrical characteristics dynamic electrical characteristics timing: spi port, in[0]/ in[1] signals & autoretry required low time allowing delatching or triggering sleep mode (direct inputs) t in 175 250 325 ms watchdog timeout for entering fail-safe mode due to loss of spi contact (38) t wdto 217 310 400 ms auto-retry repetition period (when activated): auto_period bits = 00 ? auto_period bits = 01 ? auto_period bits = 10 ? auto_period bits = 11 t auto_00 t auto_01 t auto_10 t auto_11 105 52.5 26.2 13.1 150 75 37.5 17.7 195 97.5 47.8 24.4 ms gnd pin temperature sensing function thermal prewarning detection threshold (39) t otwar 110 125 140 c temperature sensing output voltage @ t a = 25 c (470 ? < r csns < 10 k ?? t feed 918 1078 1238 mv gain temperature sensing output @ t a = 25 c (470 ? < r csns < 10 k ?? (39) dt feed 10.7 11.1 11.5 mv/c temperature sensing error, range [-40 c, 150 c], default (39) t feed_error -15 ? +15 c temperature sensing error, [-40 c, 150 c] after 1 point calibration @ 25 c (39) t feed_error _cal -5.0 ? +5.0 c notes: 38. only when the wd_dis bit set to logic [0] (default). watc hdog timeout defined from the rising edge on rst to rising edge hs[ 0,1] 39. values were obtained after lab characterization table 4. dynamic electrical characteristics (continued) unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c,v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 19 10XSD200 electrical ch aracteristics dynamic electrical characteristics spi interface electrical characteristics (40) maximum operating frequency of the serial peripheral interface (spi) (46) f spi ? ? 8.0 mhz required low-state duration for reset rstb (41) t wrstb 10 ? ? ? s required duration from the rising to the falling edge of csb (required setup time) (42) t csb 1.0 ? ? ? s rising edge of rstb to falling edge of csb (required setup time) (42) t enbl 5.0 ? ? ? s falling edge of csb to rising edge of sclk (required setup time) (42) t lead 500 ? ? ns required high state duration of sclk (required setup time) (42) t wsclkh 50 ? ? ns required low state duration of sclk (required setup time) (42) t wsclkl 50 ? ? ns falling edge of sclk to rising edge of csb (required setup time) (42) t lag 60 ? ? ns si to falling edge of sclk (required setup time) (43) t si (su) 37 ? ? ns falling edge of sclk to si (required setup time) (43) t si (hold) 49 ? ? ns so rise time c l = 80 pf t rso ? ? 20 ns so fall time c l = 80 pf t fso ? ? 20 ns si, csb, sclk, max. rise time allowing operation at f spi = 8.0 mhz (43) t rsi ? ? 12 ns si, csb, sclk, max. fall time allowing operation at f spi = 8.0 mhz (43) t fsi ? ? 12 ns time from rising edge of sclk to the so low-level (44) t so(en) ? ? 73 ns time from rising edge of sclk to the so high-level (45) t so(dis) ? ? 73 ns notes 40. parameters guaranteed by design. it is recommended to ti e unused spi pins to gnd with resistors 1.0k < r <10 k 41. rstb low duration defined as the minimum time required to switch o ff the channel when previously put on in spi mode (direct inputs inactive). 42. minimum setup time required for the device is the minimum requi red time that the microcontroller must wait or remain in a gi ven state. 43. rise and fall time of incoming si, csb, and sclk signals. 44. time required for output data to be avail able for use at so, measured with a 1.0 k ?? series resistor ? connected csb. 45. time required for output data to be terminated at so measured with a 1.0 k ?? series resistor ? connected csb. 46. for clock frequencies > 4.0 mhz, series resistors on the spi pins should preferably be removed. otherwise, 470 pf (v max. > 40 v) ceramic speed-up capacitors in parallel with the >8.0 k ? input resistors are required on pins sclk, si, so, and cs. table 4. dynamic electrical characteristics (continued) unless specified otherwise: 8.0 v ? v pwr ? 36 v, 3.0 v ? v dd ? 5.5 v, - 40 ? c ? t a ? 125 ? c, gnd = 0 v. typical values are average values evaluated under nominal conditions t a = 25 c,v pwr = 28 v & v dd = 5.0 v, unless specified otherwise. parameter symbol min typ max unit free datasheet http:///
analog integrated circuit device data ? 20 freescale semiconductor 10XSD200 electrical characteristics timing diagrams timing diagrams figure 4. output voltage slew rate and delay figure 5. overcurrent protecti on profile for bulb applications v pwr v hs[0:1] t dly_xx t dly_xx low logic level 80% v pwr 20% v pwr sr f sr r 50%v pwr r pwm range defined for 50% of v pwr csb high logic level v hs[0:1] time time time low logic level in[0:1] high logic level time or (t dly(on) ) (t dly(off) ) i och 1 t ocm2_l t ocm1_l t och1 time load current i och2 i ocm1 i ocl1 i ocl2 i ocm2 t och2 bulb profile: confs = 0 (v (pin 5/6) <0.8 v). static overcurrent protection pr ofile activated once per turn-on. default levels shown as solid lines i ocl3 free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 21 10XSD200 electrical ch aracteristics timing diagrams figure 6. overcurrent protection profile for appli cations with inductive loads (dc motors, solenoids) figure 7. timing requirements during spi communication i och 1 t ocm2_m t ocm1_m t och1 time load current i och2 i ocl1 i ocl2 t och2 inductive load profile: confs = 1 (v (pin 5/6) > 2.0 v) default levels shown as solid lines dynamic overcurrent window, activated when the i oclx threshold is crossed load current i ocl3 rstb csb sclk si don?t care must be valid don?t care v ih v il t wrstb v ih v il v ih v il v ih v il must be valid t enbl 10% v dd 10% v dd t lead t wsclkh 90% v dd 10% v dd t rs 90% v dd t csb t lag t fs t wsclkl t si(su) t si(hold) 90% v dd 10% v dd don?t care free datasheet http:///
analog integrated circuit device data ? 22 freescale semiconductor 10XSD200 electrical characteristics timing diagrams figure 8. timing diagram for serial output (so) data communication figure 9. synchronous & track-and-hold current sensing modes: associated delay & settling times sclk so v oh v ol t so(en) t valid 90% v dd 10% v dd so high to low low to high v ol v ol v oh v oh t rsi t fsi 50% 10% v dd 90% v dd t rso t fso 10% v dd t so(dis) v pwr v hs[0:1] t dly_xx t dly_xx 50%v pwr time turn-on v csns time 95% of scaled time 5.0 v 0.0 v v sync turn-off control control t csnsval_xx t syncval output current track & hold mode synchronous mode ( t dly(on) ) ( t dly(off ) (from in_s or csb) (from in_s or csb) t synread_xx see figure 4 free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 23 10XSD200 functional description introduction functional description introduction the 10XSD200 is a two-channel, high side switch that can sustain up to 36 v, with integrated control and diagnostics designed for industrial applications. the device provides a high number of protective functions. both low r ds(on) channels (<10 m ? ) can independently drive various load types like light bulbs, soleno id actuators, or dc motors. device control and diagnostics are configured through a 16-bit spi port with daisy-chain capability. independently programmable out put voltage slew rates allow satisfying electromagnetic compatibility (emc) requirements. both channels can independently be operated in three different switching modes: internal clock and internal pwm mode (fully autonomous operation), external clock and internal pwm mode, and direct control switching mode. current sensing with an adjustable ratio is available on both channels, allowing both high-current (bulbs) and low- current (led) monitoring. by activating the track & hold mode, current monitoring can be performed during the switch-off phase. this allows random access to the current sense functionality. a pate nted offset compensation technique further enhances current sense accuracy. to avoid turning off upon inrush current, while being able to monitor it, the device feat ures a dynamic overcurrent threshold profile. for bulbs, this profile is a stair function with stages of which the height and width are programmable through the spi port. dc motors can be protected from overheating by activating a specific window-shaped overcurrent profile that allow st all currents of limited duration. whenever communication with the external micro- controller is lost, the device enters fail-safe operation mode, but remains operational, controllable and protected. pin assignment and functions all logic input and output ?pins? must be protected by series resistors of at least 1.0 kohm, unless specified otherwise. functions and regist er bits that are implemented independently for both channels have extension ?_s?. output current monitoring (csns) the cs pin allows independent current monitoring of channel 0 or channel 1 up to the steady-state overcurrent threshold. it can also be used to sense the device temperature. the different func tions are selected by setting bits csns1_en and csns0_en to the appropriate value ( table 22 ). when the csns pin is sensed during switch-off in the (optional) track & hold mode (see figure 9 ), it outputs the scaled value of the load current as it was just before turn-off. when several devices share the same pull-down resistor, the csns pins of devices, the curre nt of which is not monitored, must be tri-stated. this is accomplished by setting csns0_en = 0 and csns1_en = 0 in their gcr register ( table 11 ). settling time (t csnsval_xx ) is defined as the time between the instant at the midd le of the output voltage?s rising edge (hs[0:1] = 50% of v pwr ), and the instant at which the voltage on the csns pin has settled to 5.0% of its final value. anytime an overcurrent window is active, the csns pin is disabled (see overcurrent detectio n on resistive and inductive loads ). the current and temperature sensing functions are unavailable in fail-safe mode and in normal mode when operating without the v dd supply voltage. in order to generate a voltage output, this pin requires a pull- down resistor (r(csns)=1.0 k ? typ. and 470 < r(csns) < 10 k). when the current sense re sistor connected to the csns pin is disconnected, the csns voltage is clamped to v cl(csns) . the csns pin can source currents up to about 5.6 ma. current sense synchronization (sync) to synchronize current sensing with an external process, the sync signal can be connected to a digital input of an external mcu. an open-drain pull-down on sync indicates that the current sense signal is accurate and ready to be read. the current sense sign al on the csns pin has the specified accuracy t synread_xx seconds after the falling edge on the sync pin ( figure 9 ) and remains valid until a rising edge is generated. the rising edge that is generated by the sync pin at the turn-off in stant (internal or external) may also be used to implement synchronization with the external mcu. parameter t syncval_xx is defined as the time between the instant at the middl e of the output voltage rising edge (hs[0:1] = 50% of vpwr), and the instant at which the voltage on the sync-pin drops below 0.4 v (v sol ). the sync pins of different devices can be connected together to save micro-controller input channels. however, in this configuration, the csns of onl y one device should be active at a time. otherwise, the mcu is not be able to determine the source of the sync signal. the sync pin requires an external pull-up resistor to v dd . direct control inputs (in0 and in1) the in[0:1] pins allow direct control of both channels. a logic [0] level turns off the channel and a logic[1] level turns it on. when the device is in sleep mode, a transition from logic 0 to logic 1 on any of these pins wakes it up ( channel configuration through the spi ). if it is desired to automatically turn on the channels after a tr ansition to fail-safe mode, inputs in[0] and in[1] must be externally connected to the vpwr pin by a pull-up resistor (e.g. 10 k ?? typ ?? . however, free datasheet http:///
analog integrated circuit device data ? 24 freescale semiconductor 10XSD200 functional description pin assignment and functions this prevents the device from going into sleep mode. both in pins are internally connected to a pull-down resistor. configuration inputs (conf0 and conf1) the conf[0 :1] input pins allow configuring both channels for the appropriate load type. conf = 0 activates the bulb overcurrent protection profile, and conf = 1 the dc motor profile. these inputs are connected to an internal voltage regulator of 3.3 v by an internal pull-up current source i up . therefore, conf = 1 is the default value when these pins are disconnected. details on how to configure the channels are given in the table overcurrent profile selection . fault status (fsb) this open-drain output is asserted low when any of the following faults occurs (see fault mode ): overcurrent (oc), overtemperature (ot), ou tput connected to v pwr , severe short-circuit (sc), openload in on state (ol_on), openload in off state (ol_off), external clock-fail (clock_fail), overvoltage (o v), undervoltage (uv). each fault type has its own assigned bit inside the statr, faultr_s, or diagr_s regist er. fault type identification and fault bit reset are accomplished by reading out these registers. the registers are part of the so register ( table 12 ), and are accessed through the spi port. pwm clock (clock) this pin is the input for an external clock signal that controls the internal pwm module.the clock signal is monitored by the device. the pwm module controls on-time and turn-on delay of the selected channels. the clock pin should not be confused with t he sclk pin, which is the clock pin of the spi interface. clock has an internal pull-down current source (i dwn ) to gnd. reset (rstb) all spi register contents are reset when rstb = 0. when rstb = 0, the device returns to sleep mode t in sec. after the last falling edge of the last acti ve in[0:1] signal. as long as the reset input (rstb pin) is at logic 0 and both direct input states remain low, the device remains in sleep mode ( channel configuration through the spi ). a 0-to-1 transition on rstb wakes the device and starts a watchdog timer to check the continuous presence of the spi signals. to do this, the device monitors the contents of the first bit (wdin bit) of all spi words, following that tran sition (regardless the register it is contained in). when this c ontents is not alternated within a duration t wdto , spi communication is considered lost, and fail-safe mode is entered ( entering fail-safe mode ). rstb pin is internally pulled to gnd by a r dwn resistor. chip select (csb) data communication over the spi port is enabled when the csb pin is in the logic [0] stat e. data from the input shift registers are locked in the a ddressed si registers on the rising edge of csb . the device transfers the contents of one of the eight internal registers to the so register on the falling edge of csb . the so output driver is enabled when csb is logic [0]. csb should transition from a logic [1] to a logic [0] state only when sclk is at logic [0]. csb is internally pulled up to v dd through i up . (see figure 7 and figure 8 ). spi serial clock (sclk) the sclk pin clocks the spi data communication of the device. the serial input pin (si) transfers data to the si shift registers on the falling edge of the sclk signal while data in the so registers are transferred to the so pin on the rising edge of the sclk signal. the sclk pin must be in low state when csb makes any transition. for this reason, it is recommended to have the sclk pin at a logic [0] state when the device is not accessed ( csb logic [1] state). when csb is set to logic [1], signals at the sclk and si pins are ignored and the so output is tri-stated (high-impedance). the sclk pin is connected to an internal pull-down current source i dwn . serial input (si) serial input (si) data bits are shifted in at this pin. si data is read on the falling edge of sclk. 16-bit data packages are required on the si pin (see figure 7 ), starting with bit d15 (msb) and ending with d0 (lsb). all the internal device registers are addressed and controlled by a 4-bit address (d9-d12) described in table 10 . register addresses and function attribution are described in table 11 . the si pin is internally connected to a pull-down current source, i dwn . supply of the digital circuitry (vdd) this pin supplies the spi circuit (3.3 v or 5.0 v). when lost, all circuitry is supplied by a v pwr derived voltage, except the spi?s so shift-register, which can no longer be read. ground (gnd) this is the gnd pin common for both the spi and the other circuitry. positive supply pin (vpwr) this pin is the positive supply and the common input pin of both switches. a 100 nf ceramic capacitor must be connected between vpwr and gnd, close to the device. in addition, it is recommended to place a ceramic capacitor of at least 1.0 f in parallel with this 100 nf capacitor. serial output (so) the so pin is a tri-stateable output pin that conveys data from one of the 13 internal so registers, or from the previous si register, to the outside world. the so pin remains in a high-impedance state (tri-state) until the csb pin becomes logic [0]. it then transfers the spi data (device state, configuration, fault information) . the so pin changes state at the rising edge of the sclk signa l. for daisy-chaining, it can be read out on the falling edge of sclk. v dd must be present before the so registers can be read. the so register assignment is described in ta b l e 12 . free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 25 10XSD200 functional description functional internal block description output pins (hs0 and hs1) hs0 and hs1 are the output pins of the power switches to be connected to the loads. a ceramic <= 22 nf (+/- 20%) capacitor is recommended between these pins and gnd for optimal emc performances. fail-safe output (fsob) this pin (active low) is used to indicate loss of spi communication or loss of spi supply voltage, v dd. this open- drain output requires an external pull-up resistor to vpwr. functional internal block description power supply the device operates with supply voltages from 6.0 to 58 v (v pwr ), but is full spec. compliant between 8.0 and 36 v. the vpwr pin supplies power to the internal regulator, analog, and logic circuit blocks. the vdd pin (5.0 v typ.) supplies the output register of the serial peripheral interface (spi). consequently, the spi registers cannot be read without presence of v dd . the employed ic architecture guarantees a low quiescent current in sleep mode. switch output pins hs0 & hs1 hs0 and hs1 are the output pi ns of the power switches. both channels are protected against various kinds of short- circuits and have active clamp circuitry that may be activated when switching off inductive loads. many protective and diagnostic functions are available. for large inductive loads, it is recommended to use a freewheeling diode. the device can be configured to control t he output switches in parallel, which guarantees good switching synchronization. communication interface and device control in normal mode the output channels can either be controlled by the direct inputs or by the internal pwm module, which is configured by the data stored in the spi registers. for bidirectional spi communication, v dd has to be in the authorized range. failure diagnostics and configurations are also performed through the spi port. the reported failure types are: openload, short-circ uit to supply, severe short- circuit to ground, overcurrent, overtemperature, clock-fail, undervoltage, and overvoltage. the spi port can be supplied either by a 5.0 v or by a 3.3 v voltage supply. for direct input control, v dd is not required. a pulse width modulation (pwm) circuit allows driving loads at frequencies up to 1.0 khz from an external or an internal clock. spi communication is required to set these options. power supply mcu interface and output control spi interface parallel control inputs pwm controller self- protected high side switches hs0-hs1 mcu interface internal regulator free datasheet http:///
analog integrated circuit device data ? 26 freescale semiconductor 10XSD200 functional device operation operation and operating modes functional device operation operation and operating modes the device possesses two high side switches (channels) each of which can be controlled independently. the device has four fundamental operating modes: sleep, normal, fail- safe, and fault mo de, as shown in table 5 . each channel can be controlled in three different ways in normal mode: by a signal on the direct input pin, by an internal clock signal (autonomous operation) or by an external clock signal. for bidirectional spi communication, a second supply voltage is required (v dd = 5,0 v or 3.3 v). when only the direct inputs in[x] are used, v dd isn?t required. device start-up sequence to put the device in a known configuration and guarantee predictable behavior, the device must undergo a wake-up sequence. however, it should not be woken up earlier than the moment at which v pwr has exceeded its undervoltage threshold, v pwr (uv), and v dd has exceeded its supply failure threshold, v dd (fail). in applications using the spi port, the device is typically put in wake mode by setting rstb=1. wake-up of applications with direct input control can be achieved by having signals in_on[0] = 1 or in_on[1 ]= 1 (see figure 10 ). after wake-up, all spi register contents are reset and normal mode is entered (as defined in table 11 and table 12 ). all the device functions are available 50 s later (typically). if the start-up sequence is not performed at device start- up, its configuration may be undetermined and correct operation is not guaranteed. in situations where the above described start-up sequence can not be performed, it is recommended to generate a wake-up event after the moment v pwr has reached the undervoltage threshold. channel configuration through the spi setting the channe l configuration the channel configuration is de termined by the contents of the pulse-width (pwmr_s), the configuration (confr_s) and the overcurrent (ocr_s) regi sters. they allow setting, among others, the fo llowing parameters: du ty-cycle, delay, slew rate, pwm enable (p wm_en), clock selection (clock_sel), prescaler (pr), and direct_input disable (dir_dis). extension ?_s? means that these registers exist for each of both channels. function assignment is described in detail in the section si register addressing reading back the channel?s status and settings the channel?s global switchi ng and operating states (on/ off, normal/fault) are all contained in the statr register (see table 12 ). the precise fault type can be found by reading out the faultr_s and statr registers. the channel? settings (channel configuration) can be read back by reading the pwmr, conf, ocr, retry, gcr, and diag registers. for more information, see serial output register assignment . normal mode normal mode (bit nm = 1) can be entered in two ways, either by driving the device through the direct inputs in[x], or by establishing spi communication (requires rstb =high). bidirectional spi communicatio n additionally requires the presence of v dd . to maintain the device in normal mode, communication must take place regularly (see entering and maintaining normal mode ). the device is in normal mode (nm) when: ?v pwr (and v dd ) are within the normal range and ? wake-up = 1, and ? fail-safe = 0, and ? fault = 0. channel control in normal mode in direct input mode, the channel?s switching state (on/off) basically follows the logic state of the direct input signal with the turn-on delay and slew rate specified in table 4 . in internal clock mode, the s witching state is controlled by an internal clock signal ( internal clock & internal pwm (clock_int_s bit = 1) ). frequency, slew rate, duty-cycle, and turn-on delay are programmable independently for both channels. in external clock mode, the frequency of the external clock controls the output's pwm frequency, but slew rate, duty cycle, and turn-on delay are still programmable. factors determining the channel?s switching state the switching state of a ch annel is defined by the instantaneous value of the output voltage. it is defined as ?on? when the output vo ltage v(hs[x]) > v pwr /2 and ?off? when v(hs[x]) < v pwr /2. the channel?s switching state should not be confused with the device?s internal channel control state hson[x] (= high side on). signal hson[x] defines the targeted switching state of the channel (on/off). it is either controlled by the value of the direct input signal or by that of the internal/external clock signals combined with the spi register settings. the value of hson[x] is given by the following boolean expression: hson[x] = [(in[x] and dir_dis[x] ) or (on bit [x] and duty_cycle[x] and pwm_en[x] = 1) or (on bit [x] and pwm_en[x] = 0)]. in this expression duty_cycle[ x] represents the value of the duty cycle, set by bits d7?d0 of the pwmr register ( table 6 ). the channel?s actual switching state may differ from the control signal?s st ate in the following cases: ? short circuits to gnd, befor e automatic turn-off (t < t fault ) ? short circuits to v pwr when the channel is set to off free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 27 10XSD200 functional device operation operation and operating modes ?v pwr < 13 v when openload in off state detection is selected and the load is actually lost ? during the turn-on transition as long as v(hs[x])< v pwr /2 ? during the turn-off transitio n as long as v(hs[x]) > v pwr /2 entering and maintaining normal mode a 0-to-1 transition on rstb, (when both v pwr and v dd are present) or on any of both di rect inputs in[x] (when only supplied by v pwr ), puts the device in normal mode. if desired, the device can be op erated in normal mode without v dd , but this requires that at leas t one of both direct inputs be regularly turned on ( operation and operating modes ). to maintain the device in norm al mode (nm), communication must take place on a regular basis. for spi communication, the stat e of the wdin bit must be alternated at least every 310 ms (typ.) (t wdto ), unless the wd_disable bit is set to 1. for direct input control, the timing requirements are shown in figure 10 . a signal called in_on[x] is not directly accessible to the user but is used by the internal logic circuitry to determine the device state. when no activity is detected on a direct input pin (in[x]) for a time longer than t in = 250 ms (typ.), timeout is de tected and in_on[x] goes low. when this occurs on both channels, sleep mode is entered ( sleep mode ), provided reset = rstb = 0 . figure 10. relation between signals in(x) and in_on[x] direct control mode when rstb = 0 (and also in fail-safe mode), the channels are merely controlled by the direct input pins in[x]. all protective functions (oc, ot, sc, ov, and uv) are operational including auto-retry. to avoid entering sleep mode at frequencies < 4.0 hz, reset should be set to rstb = 1. going from normal to fail-safe, fault or sleep mode the device changes from normal to fail-safe ( fail-safe mode ), sleep mode ( sleep mode ), or fault mode ( fault mode ), according to the value of the following signals (see table 5 ). ? wake-up = rstb or in_on[0] or in_on[1] ? fail-safe = (v dd failure and v dd _fail_en) or (spi watchdog timeout (t wdto ) and wd _dis = 0) ?fault = oc[0:1] or ot[0:1] or sc[0:1] or uv or (ov and ov _disb ) it enters fail-safe mode, when either a timeout on spi communication or when v dd is lost, after having been initially present (if this function was previously enabled by setting: v dd _ fail _ en bit = [1]). setting watchdog disabled (wd_dis = 1, d4 of the gcr register) avoids entering fail- safe mode after a watchdog timeout. device behavior upon fault occurrence is explained in the paragraph on faults ( fault mode ). in_on[x] in[x] t in table 5. device operating modes mode wake-up fail- safe fault comments sleep 0 x x all channels are off. normal 1 0 0 the spi watchdog is active when: v dd = 5.0 v, wd_dis = 0, rstb = 1 fail-safe 1 1 0 the channels are controlled by the in inputs. (see fail-safe mode ) fault 1 x 1 the channels are off, see fault mode . x = don?t care. free datasheet http:///
analog integrated circuit device data ? 28 freescale semiconductor 10XSD200 functional device operation operation and operating modes figure 11. device operating modes sleep mode in sleep mode, the channels and the spi interface are turned off to minimize current consumption. the device enters sleep mode (wake-up = 0) when both direct input pins in(x) remain off longer than t in sec. (when reset is active; rstb = 0). this is expressed as follows: ?v pwr (and v dd ) are within the normal range, and ? wake-up = 0 (wake-up = rstb or in_on[0] or in_on[1]), and ? fail-safe = x, and ?fault = x when employed, v dd must be kept in the normal range. sleep mode is the default mode after the first application of the supply voltage (v pwr ), prior to any i/o communication (rstb and the internal states in_on[0:1] are still at logic [0]). all spi register contents remain in their default state during sleep mode. fail-safe mode entering fa il-safe mode fail-safe mode is entered either upon loss of spi communication or after loss of optional spi supply voltage v dd ( vdd out of range ). the fsob pin goes low and the channels are only controlled by the direct inputs (in[0:1]). all protective functions remain fully operational. previously latched faults are delatched and spi register contents is reset (except bits por & parallel) . the spi registers can not be accessed. these conditions are also described by the following expressions: ?v pwr is within the normal voltage range, and ? wake-up = 1, fault = 0, and ? fail-safe = 1 ((v dd failure and v dd _fail_en=1 before) or (t(spi)> t wdto and wd_dis = 0). the second case corres ponds to loss of spi communication, which is detai led in the next section. watchdog on spi communication and fail-safe mode when v dd is present, the spi watchdog timer is started upon a rising edge on the rstb pin. thereafter, the device monitors the state of the first bit (wdin) of all received spi words. when the state of this bit is not alternated at least once within a data stream of duration t wdto = 310 ms typ. , the device considers the spi communication has been lost and enters fail-safe mode. this behavior can be disabled by setting the bit wd_dis = 1. the value of watchdog timeout is derived from an internal oscillator . returning from fail- safe to normal mode to exit fail-safe mode and return to normal mode again, first a spi data word with its wdin bit = 1 (d15) must be received by the device (regardless the register it is contained in, and regardless of the values of the other bits in this register). next, a second data word must be received within the timeout period (t wdto = 310 ms typ.), to be able to change any spi register contents. upon entering normal sleep (fail-safe = 0) and (wake-up = 1) and (fault = 0) (wake-up = 0) fail-safe normal (wake-up = 0) (fail-safe = 1) and (wake- up = 1) and (fault = 0) (fail-safe = 0) and (wake- up = 1) and (fault = 0) (wake-up = 1) and (fail-safe = 1) and (fault = 0) fault (wake-up = 0) (wake-up = 1) and (fault = 1) (fail-safe = 0) and (wake-up = 1) and (fault = 1) (fail-safe = 1) and (wake-up = 1) and (fault = 1) (fail-safe = 0) and (wake- up = 1) and (fault = 0) (fail safe = 1) and (wake-up = 1) and (fault = 0) free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 29 10XSD200 functional device operation operation and operating modes mode, the fsob pin returns to logic high and previously set faults and spi registers are reset, except bits por, parallel and fault bits of latchable faults that had actually been latched. fault mode the device enters fault mode when any of the following faults occurs in normal or fail-safe mode: ? overtemperature fault, (latchable fault) ? overcurrent fault, (latchable fault) ? severe short-circuit fault, (latchable fault) ? output shorted to v pwr in off state (default: disabled) ? openload fault in off st ate (default: disabled) ? openload fault in on st ate (default: disabled) ? external clock failure (default: enabled) ? overvoltage fault (enabled by default) ? undervoltage fault, (latchable fault) the fault status pin ( fsb) asserts a fault occurrence on any channel in real time (a ctive low). additionally, the assigned fault bit in the statr_s or faultr_s register is set to one. conversely to the fsb pin, a fault bit remains set until the corresponding register is read, even if the fault has disappeared. these bits can be read via the so pin. fault occurrence also results in a turn-off of the incurred channel, except for the following faults : openload (on and off state), external clock failure and output(s) shorted to v pwr . under and overvoltage occurrences cause simultaneous turn-off of both channels. details on the device?s behavior, after the occurrence of one of the above faults can be found in protection and diagnostic features . fault mode ( operation and operating modes ) is entered when: ?v pwr (+v dd ) were within the normal voltage range, and ? wake-up = 1, and ? fail-safe = x, and ?fault = 1 (see going from normal to fail-safe, fault or sleep mode ) resetting fault bits registers statr_s and faultr_s contain global and channel-specific fault information. reading the register the fault bit is contained in, clears it, provided a failure cause disappearance has been detected and the fault wasn?t latched. entering fault mode from fail-safe mode when a fault occurs in fail-safe mode, the device is in fault/fail-safe mode and behaves according to the description of fault mode. ho wever, spi registers remain reset and can not be accessed. only the direct inputs control the channels. returning from fault mode to fail-safe mode when disappearance of the fault previously produced in fail-safe mode has been detected, the device returns to fail- safe mode and behaves accordingly. fsb goes high, but the auto-retry counter is not rese t. latched faults are not delatched. spi registers remain reset. latchable faults an auto-retry function (see auto-retry ) controls how the device responds to the so-called latchable faults. latchable faults are: overcurrent (oc) , severe short-circuit (sc), overtemperature (ot), and undervoltage (uv). if a latchable fault occurs, the channel is turned off, the fsb pin goes low, and the assigned fault bit is set. these bits can not be reset before the next turn-on even t is generated by auto-retry. next, the channel is automatically turned on at a programmable interval, provided auto-retry was enabled and the channel wasn?t latched. if the failure disappears prior to the expiration of the available number of auto-retries, the fsb pin automatically returns to logic [1], but the fault bit remains set. it can still be reset by reading out the spi register in which it is contained. however, the fault actually gets latched if the failure cause hasn?t disappeared at the first turn-on event following expiration of the available amount of auto-retries (see auto- retry ). in that case, the channel gets latched and the fsb pin remains low. the fault bit can only be reset by reading out the associated spi register, after having performed a delatch sequence ( fault delatching ). fault delatching to delatch a latched channel and be able to turn it on again, a delatch sequence must execute after the disappearance of the failure cause. delatching also allows to reset the fault bit of latched faults (see resetting fault bits ). to reset the fsb pin, both channels must be delatched. delatching is achieved by eit her alternating the state of the channels? fault control signal fc[x] (generating a 1_0_1 sequence), or by resetting the auto-retry counter (provided retry is enabled). (see reset of the auto-retry counter ) delatching then actually occurs at the rising edge of the turn- on event. signal fc[x] is an internal signal used by the device?s internal logic circuitry to control the diagnostic functions. the value of fc[x] depends on the st ate of the variables in_on[x], dir_dis[x] and on[x] and is expressed as follows: fc[x] = ((in_on[x] and dir_dis[x] = 0) or on[x] = 1) alternating the fc[x] signal is achieved differently according to the way the user controls the device. ? in direct-input controlled mode (dir_dis_s = 0), the in[x] pin must be set low, remain low for at least t in seconds, and set high again (be switched on). this might happen automatically when operating at frequencies, f<4.0 hz. ? in spi-controlled mode, the on_bit state (d8 of the pwmr_s reg.) must be alternat ed (?toggled?). no minimum off state duration is required in this case. performing a delatch sequence anytime during an ongoing auto-retry sequence (before la tching) allows turning the channel on unconditionally. free datasheet http:///
analog integrated circuit device data ? 30 freescale semiconductor 10XSD200 functional device operation operation and operating modes when a power-on event occurs (see loss of vpwr , loss of vdd and power-on-reset (por) ), latched channels are also delatched and faults are reset. when fail-safe mode is ent ered (fault=1, fail-safe becomes 1) during operating in fault mode (fault=1, failsafe=0), previously latched faults are delatched and spi register content is reset (exc ept bits por & parallel). the device is then in a combined fail-safe/fault mode. when the device was already in fail-safe mode (fault=1, failsafe=1) and (new) faults occurs, the internal auto-retry counter is not reset and latched channels are not delatched until a delatching sequence has been performed (see protection and diagnostic features ). programmable pwm module each channel has a fully independent pwm module activated by setting pwm_en_s. it modulates an internal or external clock signal. setting clock_int_s = 1 (bit d6 of the ocr_s register) activates the internal clock, and setting clock_int_s = 0 activates the external clock. the duty cycle can be set in a range from 0 to 100% with 8 bit-resolution ( table 6 ) by setting bits d8?d0 of the pwmr_s register ( table 11 ). the channel?s switching frequency equals the clock frequency divided by 256 in internal clock mode, and by 256 or 512 in external clock mode. figure 12. internal and external clock operation . by delaying the activation of one channel relative to the other ( table 7 ), switch-on surges can be delayed, which may improve emc performance. switch-on delay can be selected among seven different values (default=0) by setting bits d2?d0 of the confr_s register (expressed as a number of ext./int. pwm clock periods). to start the pwm function at a known point in time, the pwm_en_s bit (d8 /d7 of the gcr reg.) must be set to 1 after having set the pwmr_s (duty cycle) and confr_s (delay) r egisters. the best way to optimize emc is to use an external clock with a staggered switch on delay. external clock & inte rnal pwm (clock_int_s = 0) the channels can be controlled by an external clock signal by setting bit d6 =0 of the ocr_ s register (clock_int_s). duty cycle values specified in table 6 apply. when an external clock is used, the value of frequency division (256 when pr[x] = 0) may be doubled by setting the prescaler bit pr[x]) = 1(bit d7 of the ocr_s reg.). this allows driving the channels at different switching frequencies from a single clock signal. simultaneously setting pwm_en_1=1 and pwm_en_0=1 synchro nizes the channels. the clock frequency on the clock pin is monitored when external clock (clock_int_s = 0) and pulse width modulation (pwm_en_s = 1) are both selected. if a clock failure occurs under these conditions (f< f clock(low) or f> f clock(high) ), the external clock signal is ignored and a fault is detected (fsb =0), clock_fail bit is set (od2 in the diagr register). the state of t he on_s bit in the spi register then determines the channel?s s witching state. to return to external clock mode (and reset fsb), the clock-fail bit must be read and the external clock has to be within the authorized range again. internal clock & internal pwm (clock_int_s bit = 1) by using a reference time slot (usually available from an external microcontroller), the period of each of the internal pwm clocks can be changed or calibrated (see programmable pwm module ). calibration of the default period = 1/f pwm(0) reduces its maximum variation from about +/-30 percent to +/- 10%. the programming procedure is activated by sending a dedicated word to the si-calr register (see table 11 ). next, the device sets the new value of the switching period in 2 steps . first it measures the time elapsed between the first falling edge on the csb pin and the next rising edge on the csb pin (t csb ). then it changes the value of the internal clock period accordingly. the actual table 6. pwm duty cycle value assignment on-bit duty cycle channel configuration 0 x off 1 00000000 pwm (1/256 duty cycle) 1 00000001 pwm (2/256 duty cycle) 1 00000010 pwm (3/256 duty cycle) 1 n pwm ((n+1)/256 duty cycle) 1 11111111 fully on software configurable external clock frequency monitoring clock cs in_x internal clock calibration mux pr_x ?? (1 + pr_x) clock_fail clock_sel_x internal oscillator ?? 256 pwm mode hs_x driver block pwmr_s register pwm_en_x vpwr hsx table 7. switch-on delay in pwm mode delay bits switch-on delay 000 no delay 001 32 pwm clock periods 010 64 pwm clock periods 011 96 pwm clock periods 100 128 pwm clock periods 101 160 pwm clock periods 110 192 pwm clock periods 111 224 pwm clock periods free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 31 10XSD200 functional device operation operation and operating modes value of the channel?s switching period is obtained by multiplying the internal clock period by 256. when the duration of the negative csb pulse is outside a predefined time slot (from t csb(min) to t csb(max) ), the calibration event is ignored and the internal clock frequency remains unchanged. if the value (f pwm(0) ) has not been previously calibrated, it remains at its default level. synchronization of both channels when internal clock signals are used to drive the pwm modules, perfect synchronization over a long time can not be achieved, since both clock signals are independent. however, when the channels are driven by the external clock, perfect synchronization can be achieved by simultaneously setting pwm_en_1=1 and pwm_en_0=1. the best way to optimize emc is to use an ex ternal clock with a staggered switch on delay (see table 7 ). parallel operation the channels can be paralleled to drive higher currents. setting the parallel bit in the gcr register to logic [1] is mandatory in this case. the improved synchronization of both transistors allows an equal current distribution between both channels. in parallel mo de, both output pins (hs[x]) must be connected, as well as both in[x] pins, in case of external control. conf0 and conf1 must be set to equal values. 1- device configuration in parallel mode: there are two ways to config ure the on/off control: spi control and direct input control. ? spi controlled parallel mode : the switching configuration is solely defined by the (si) pwmr_0, confr_0, ocr_0, and retry_0 registers. as soon as parallel=1, the contents of the corresponding registers in bank 1 is replaced by that of bank 0, except bits d6-d8 of the confr_1 register (configuration openload/ output short-circuited diagnostics). it is recommended to disable the off-state openload for the hs1 output. after setting parallel=1, contents of so registers in bank 0 are copied to the registers of bank 1 only when new information is written in them. bits od3, od4 and od5 of both faultr_s registers are a lways reported independently. ? direct input mode: the in0 and in1 pins must be connected externally. 2- diagnostics in parallel mode: the diagnostics in parallel mode operate as follows: ? openload in off state and - openload in on state: the ol_on and ol_off bits of both faultr registers independently report failures of the channels according to the settings of bits d7 and d6 of the confr_s register. ? current sensing: refer to the table 22 for a description of the various current sensing modes. only the current sense ratio of bank 0 (d5 of the ocr_0 register) is considered. the corresponding bit in the ocr_1 register is copied from t hat of the ocr_0 register. ? output shorted to supply: the os-bit (od3) of each of both fault registers independently report this fault, according to the settings of bit d8 of the confr_s reg. 3- protections in parallel mode: ? overcurrent: -only the configuration of overcurrent thresholds & blanking windows of channel 0 are considered. -in case overcurrent (oc) occurs on any channel, both channels are turned-off. regardless the order of occurrence of oc, both oc-bits (od0) in the fault registers are simultaneously set to logic 1. ? severe short-circuit: in case of sc detection on any channel, both channels are turned-off and the sc bits (od1) in both fault registers are simultaneously set to logic 1. ? overtemperature: in case of ot detection on any channel, both channels are turned-off and both ot bits in the fault registers (od2) are simultaneously set to logic 1. ? auto-retry: only one 4-bit auto-retry count er specifies the number of successive turn-on events on paralleled channels (retryr_0). the counter value in register retryr_1 (od4?od7) is copied from that in retryr_0. to delatch the channels, only channel 0 needs to be delatched. csb si calr_s si command ignored internal clock period of channel s t csb t csb free datasheet http:///
analog integrated circuit device data ? 32 freescale semiconductor 10XSD200 functional device operation operation and operating modes protection and diagnostic features protective functions overtemperature fault (latchable fault) the channels have individual overtemperature detection. as soon as a channel?s junction temperature rises above t sd (175 c typ.), it is turned off, the overtemperature bit (ot = od2) is set, and fsb = 0. fsb can only be reset by turning on the channel when the junction temperature of both channels has dropped below the threshold: t j 50 kohm or vih (2.0 v)< v(conf) < 5.0 v inductive: conf = 1, dc motor mode free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 33 10XSD200 functional device operation operation and operating modes profile. the channel is switched off when a threshold is crossed or a window width is exceeded. in dc motor mode, only one overcurrent window exists, defined by two different current levels, as illustrated by figure 6 . this window is opened anytime the output current exceeds the selected lo wer overcurrent level (i oclx ). in this case, the allowed overcurrent duration is defined by parameters t ocm1_m , t ocm1 , and t och2 . the selection of the different profiles and values is explained in the section address a0100 ? overcurrent protection configuration register (ocr_s) . auto-retry after overcurrent shut off when auto-retry is ac tivated, oc-latching ( overtemperature fault (latchable fault) ) only occurs after expiration of the available amou nt of auto-retries (described in auto-retry ). switch mode operation and overcurrent duration switch mode is defined as any device operation with a duty cycle lower than 100% at a frequency above f pwm_ext (min.) or f pwm_int (min.). the device may operate in switch mode in internal/external pwm or in direct input mode. in switch mode, the accumulated time spent by the load current in a particular window segm ent during on-times of successive switching periods is identified by the aforementioned duration counter, and compared to the active segment width. the associated off-times are excluded by the duration counter. the channel is turned-off when the value of the counter exceeds the window width. in figure 14 , overcurrent detection shutdown is shown in case of switch mode operation with a duty cycle of 50% (solid line) and 100% (fully-on, dashed line). the device is turned off much later in switch mode than in fully-on mode, since the duration counter only counts overcu rrent during on-times. figure 14. overcurrent shutdown in pwm mode (solid line) and non-pwm mode (dashed line) reset of the duration counter reset of the duration counter is achieved by performing a delatch sequence ( fault delatching ). in lighting mode (confs = 0), this counter is also reset automatically at each auto-retry (but not in dc motor mode). in dc motor mode, the duration counter is reset either by performing a delatch sequenc e or (automatically) after occurrence of a new on-period without any overcurrent ([hson[x]=1). reset then actually occurs at the first turn-off instant following that on-period. in switch mode, the duration co unter is not reset by normal pwm activity unless delatching is performed. severe short-circuit fault (latchable fault) when a severe short-circuit (sc) is detected at turn-on (wiring length l load < l short , table 3 ), the channel is shut off immediately. for wiring lengths above l short , the device is protected from short-circuits by the normal overcurrent protection functions ( overcurrent fault (latchable fault) ). when an sc occurs, fsb goes low (logic [0]), and the sc bit is set, eventually followed by an auto-retry. sc is of the latchable type (see protection and diagnostic features and fault delatching ). overvoltage detection (enabled by default) by default, the supply overvoltage protection (v pwr ) is enabled. when overvoltage occurs (v pwr > v pwr(ov) ), the device turns off both channels simultaneously, the fsb pin is asserted low, and the ov faul t bit is set to logic [1]. the channels remain off until the supply voltage drops below a threshold voltage v pwr < v pwr(ov) - v pwr(ovhys) . the ov bit can then be reset by reading out the statr register. the overvoltage protection can be disabled by setting the ov_dis = 1 in the general configur ation (gcr) register. in this case, the fsb pin neither asserts a fault occurrence, nor turns the channels off. however, t he fault register (ov bit) still reports an overvoltage occurrence (when v pwr > v pwr(ov) ) as a warning. when v pwr > v pwr(ov) , the value of the on- resistance on both channels (r ds(on ) ) still lays within the ranges specified in table 3 . undervoltage fault (latchable fault) the channels are always turned off when the supply voltage (v pwr ) drops below v pwr(uv) . fsb drops to logic [0], and the fault register?s (co mmon) uv bit is set to [1]. when the undervoltage condition then disappears, two different cases exist: ? if the channel?s internal control signal hson[x] is off, fsb returns to logic [1], but the uv bit remains set until at least one output is turned on (warning). ? if the channel?s control signal is on, the channel is only turned on if a delatch or por sequence is performed prior to the turn on request. the uv bit can then only be reset by reading out the statr register. auto-retry (if enabled) starts as soon as the uv condition disappears. free datasheet http:///
analog integrated circuit device data ? 34 freescale semiconductor 10XSD200 functional device operation operation and operating modes extended mode protection in extended mode (6.0 v < v pwr < 8.0 v or 36 v < v pwr < 58 v), the channels are still fa ult protected, but compliance with the specified protection le vels is not guaranteed. the register settings however (i ncluding previously detected faults) remain unaltered, provided v dd is within the authorized range. below 6.0 v, the channels are only protected from overtemperatur e, and this fault is only reported in the spi regi ster at the moment v pwr has again risen above vpwr (uv) . to allow the outputs to remain on between 36 v and 58 v, overvoltage detection should be disabled by setting ov_dis = 1 in the gcr reg.). faults (overtemperature, overcu rrent, severe short-circuit, over and undervoltage) are reset if: ?v dd < v dd(fail) with v pwr in the normal voltage rang ?v dd and v pwr are below the v supply(por) voltage threshold ? the corresponding spi regi ster is read after the disappearance of the failure cause (and delatching) drain/source overvoltage protection the device tries to limit the drain-to-source voltage by turning on the channel whenever v ds exceeds v ds(clamp) . when a fault occurs (sc, oc, ot, and uv), the device is rapidly switched off (in t < t fault seconds), regardless the value of the selected slew rate. this may induce voltage surges on v pwr and/or the output pin (hs[x]), when connected to an inductive line/load. turning on the device also dissipates the energy stored in the inductive supply line. this function monitors overvoltage for v pwr > 30 v. below v pwr < 30 v, the negative output volt age protection protects the device from overvoltage by turning on the channel. the feature remains functional after device ground loss. supply overvoltage protection in order to protect the device from excessive voltages on the supply lines, the voltage between the device?s supply pins (vpwr and the gnd) is monitored. when the v pwr -to-gnd voltage exceeds the threshold v d_gnd(clamp) , the channel is automatically turned on. the fe ature is not operational in cases of ground loss. negative output voltage protection the device tries to limit t he undervoltage on the output pins hs[x] when turning off inductive loads. when the output voltage drops below v cl , the channel is switched on automatically. this fe ature is not guaranteed after a device ground loss. the energy dissipation capabilities of the circuit are defined by the e cl [0:1] parameters. for inductive loads larger than 20 h, it is recommended to employ a freewheeling diode. the three different overvo ltage protection circuits are symbolically represented in figure 15 . the values of the clamping diodes are those specified in table 3 . coupling factor k represents the current ratio between the current in the supply voltage measurement diode (zener) and that injected into the mosfet?s gate to turn it on. . figure 15. supply and output voltage protections reverse voltage protection on v pwr the device can withstand reverse supply voltages on v pwr down to -28 v. under these condit ions, the outputs are automatically turned on and the channel?s on resistance (r ds(on) ) is similar to that during regular supply voltages. no additional components are required to protect the v pwr circuit except series resistors (>8.0 k) between the direct inputs in[0:1] and v pwr in case they are connected to v pwr . the v dd pin needs reverse voltage protection from an externally connected diode ( figure 21 ). load and system ground loss in case of load ground loss, the channel?s state does not change, but the device detects an openload fault. in case of a system gnd loss, the c hannels are turned off. device ground loss in the (improbable) case where the device loses all of its three ground connections (pins 14, 17, and 22), the channels? state (on/ off) depends on several factors: the values of the series resistors connected to the device pins, the voltage of the direct input signals, the device?s momentary current consumption (influenced by the spi settings), and the state of other high side switches on the board, when there are pins in common like fsb, fsob and sync. in the following description, all voltages ar e referenced to the system (module) gnd. when series resistors are us ed, the channel state can be controlled by entering fail-s afe mode. the channels are turned off automatically when the voltage applied to the in[x] input(s) through the series resistor(s) is not higher than v dd and be turned on when the in[x] input(s) are tied to vpwr. fail-safe is entered under the following conditions: ? all unused pins are tied to the overall system gnd connection by resistors > 8.0 k. imeg gnd loa d hs[ x] v pw r dc v ds(clamp)- v th v d_gnd (clamp) i 2 v cl- v th k.i z v th free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 35 10XSD200 functional device operation operation and operating modes ? any device pin connected to external system components has a series resistors > 8.0 k (except pins vpwr, vdd, hs[0], hs[1] and r(csns)>2.0 k) ? fsb, fsob, and sync pins are in the logic high state when they are shared with other devices. this means none of the other devices are in fault- or fail-safe mode, nor should current sensing be performed on any one of them when gnd is lost when no series resistors are employed, the channel state after gnd loss is determined by the voltage on pins in[0:1] and the voltage shift of the device gnd. device gnd shift is determined by the lowest value of the external voltage applied to either pin of the following list: clock, fsb, in[0:1], fsob, sclk, cs,si, so, rstb, conf[0:1], sync, and csns. when the device gnd voltage becomes a logic low (v(gnd)< v il ), the spi port continues to operate and the device operates normally. when the gnd voltage becomes logic high (v(gnd)> v ih ), spi communication is lost and fail- safe mode is entered. when the voltage applied to the in[0:1] input is v pwr , the channel is turned on when it is v dd , the channel is turned off if (v dd - v(gnd)) < v ih . supply voltages out of range v dd out of range if the external v dd supply voltage is lost (or falls outside the authorized range: v dd v pwr (por) , after a period v pwr < v pwr (por) (and v dd < v dd (por) before and after) ?v dd > v dd (por) after a period with v dd < v dd (por) (v pwr < v pwr (por) before and after) por is also set at the transition to wake-up (by setting rstb =1 or in[x]=1) when v pwr > v pwr (por) (before and after) or v dd >v dd(por) (before and after). por is not performed when v pwr > v pwr (por) after a period v pwr < v pwr (por) (and v dd > v dd (por) permanently). free datasheet http:///
analog integrated circuit device data ? 36 freescale semiconductor 10XSD200 functional device operation operation and operating modes figure 16. state machine: fault occurrence and auto-retry auto-retry the auto-retry circuitry automatic ally tries to turn on the channel on a cyclic basis. only faults of the latchable type (overcurrent, severe short-circuit, overtemperature (ot), and undervoltage (uv)) may activate auto-retry. for uv and ot faults, auto-retry only starts af ter disappearance of the failure cause when auto-retry is enabled. the retry condition is expressed by: retry[x] = oc[x] or sc[x] or ot[x] or uv. if auto-retry has been enabled, its mode of operation depends on the settings of the auto-retry related bits (bits d0...d3 of the si-retry_s register, see table 12 ) and the available amount of auto-retrie s (bits od7...od4 of the so- retry_s reg.). more details can be found in number of auto-retries . if auto-retry is disabled, latchable faults are automatically latched upon their occurrence (see protection and diagnostic features ). auto-retry configuration to enable the auto-retry function , bit retry_s (d0 of the si retry_s register) has to be set to the appropriate value. auto-retry is enabled for retry_s = 0 when the channel is configured for lighting applications (conf=0). it is enabled for retry_s=1 for dc motor applications (conf[x] =1). if auto-retry is enabled, an auto-retry sequence starts when the channel?s fault control signal is set to 1 (fc[x] = 1, fault delatching ) and the retry condition applies (retry[x]=1. see auto-retry ). when a failure occurs (fault = 1), the channel are automatically switched on again after the auto-retry period. the value of this period (t auto ) is set through the spi port bits (d2 and d3 of the retry_s register, see table 21 ). when the failure cause disappears before expiration of the available amount of auto-retries, the device behaves normally (fsb = 1), but the fault bit remains set until it is cleared. this guarantees a maximum device availability without preventing fault detection. number of auto-retries in case the device is configur ed for an unlimited amount of auto-retries (retry-unlimited_s = 1), auto-retry continues as off on latched off off on (ov = 1) (fc[x] = 1 and (ov = 0)) (fc[x]= 0 or ov = 1) (fc[x] = 0) (fc[x] = 0) (fc[x] = 0) (retry = 1) = > count = count+1 (retry = 1) (count = 16) (after retry period and ov = 0 and ot = 0 and uv = 0) (openloadoff = 1 or os = 1 (openloadoff = 1 or os = 1 (openloadoff = 1 or os = 1 (openloadon = 1) (openloadon = 1) or ov = 1) or ov = 1 or ov = 1) or uv = 1 or ot = 1) auto-retry loop table 9. auto-retry activation for lamps (conf=0) and dc motors (conf=1) conf[x] retry_s bit auto-retry 0 0 enabled 0 1 disabled 1 0 disabled 1 1 enabled free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 37 10XSD200 functional device operation operation and operating modes long as the device remains powered. the channel is never latched off. in case a limited amount of retries is selected (retry- unlimited_s = 0), auto-retry continues as long as the value of the 4-bit auto-retry counter does not exceed 15 (bits od4...od7 of the retry_s register). after 15 retries, the rfull bit of the statr (od4 for channel 0, od5 for channel 1) register is set to a logic hi gh. the amount of available auto- retries is then reduced to one. if the fault still hasn?t disappeared at the next retry, the corresponding channel is switched off definitively and the fault is latched (fsb = 0). see protection and diagnostic features and fault delatching . any channel can be turned on at any moment during the auto-retry cycle by performing a delatch sequence. however, this does not reset the retry counter. the value of the auto-retry counter can be read back in normal mode (so-retry register bits od7-od4). reset of the auto-retry counter the counter of the amount of retries is reset when: ? fail-safe is entered ( fail-safe mode ) ? sleep mode is left ( sleep mode ) ? por occurs ( supply voltages out of range ) ? the retry function is set to unlimited (bit retry- unlimited_s = 1 (d1 = 1)) ? the retry function is disabled (retry_s bit = d0 of the retry_s register under goes a 1-0 sequence for conf = 1 and a 0-1 sequence for conf = 0). if the channel is latched at the moment the auto-retry counter is reset (case 4), the channel is delatched, and turned on after one retry period (if retry was enabled). auto-retry and overcurrent duration during the on-period following each auto-retry, the load current profile is compared to the length and height of the selected overcurrent threshold profile, as described in the section on overcurrent protection. see overcurrent fault (latchable fault) . when the lighting profile is activated, the overcurrent duration counter is reset at each auto-retry (to allow sustaining new inrush currents). for dc motor mode however, it is only reset at the turn-off event of the first pwm period without any overcurrent (see reset of the duration counter ) figure 16 gives a description of the retry state machine with the various transitions between operating modes. diagnostic features diagnostic functions openload in on state (olon), openload in off state (oloff) and output short-circuited to v pwr (os) are operational over the frequency and duty cycle ranges specified in table 4 for pwm mode, but the precise values also depend on the way the device is controlled (direct/internal pwm), on the cu rrent sense ratio and on the optional activation of the openload in on state detection. as an example, in direct input ( dir_dis_s = 0), low-current mode (csr1), olon, oloff, and os detection are performed for duty cycle values up to: rpwm_400_h = 85% (instead of 90%) when openload in on state detection is enabled (olon_dis=0). output shorted to v pwr fault the device detects short-circui ts between the output and v pwr . the detection is performed during the off-state. the output-shorted to v pwr fault-bit (os_s) is set whenever the output voltage rises above v osd(thres) . the fault is reported in real time on the fsb pin and saved by the os_s bit. occurrence of this fault does not trigger automatic turn-off. even if the short-circuit disa ppears, the os_s bit is not cleared until the faultr register is read. the function may be disabled by setting os_dis_s=1. the function operates over the duty cycle ranges specified in diagnostic features . this type of event shall be limited to 1000 min. during its lifetime. in case of permanent output shorted to the power supply condition, it is needed to turn-on the corresponding channel. openload detection in off state openload in off state detec tion (ol_off) is performed continuously during each off state (both for csr0 and csr1). this function is impl emented by injecting a small current into the load ( i old(off) ). when the load is disconnected, the output voltage rises above v old(thres) . ol_off is then detected and the ol_off bit in the faultr register is set. if disappearance of the open load fault is detected, the fsb output pin retu rns to a high immediately, but the ol_off bit in the fault re gister remains set until it is cleared by a read out of the faultr register. the function may be disabled by setting oloff_dis_s=1. the function operates over the duty cycle ranges specified in section diagnostic features . openload detection in on state (ol_on) openload in on state detect ion (olon) is performed continuously during the on stat e for csr0 over the ranges specified in section diagnostic features . an openload in on state fault is detected when the load current is lower than the openload current threshold i old(on) . this happens at i old(on) = 300 ma (typ.) for high- current sense mode (csr0), and at 7.0 ma (typ.) for low-cu rrent mode. fsb is asserted low and the olon bit in t he fault register is set to 1, but the channel remains on. fsb goes high as soon as the disappearance of the failure cause is detected, but the ol_on bit remains set. in high current mode (csr0), openload in on state detection is done continuously during the on state and the olon-bit remains set even if the fault disappears. in high current mode, the olon-bit is cleared when the faultr register is read during the off state, even if the fault hasn't disappeared. the olon bit is also cleared when the free datasheet http:///
analog integrated circuit device data ? 38 freescale semiconductor 10XSD200 functional device operation operation and operating modes faultr register is read during the on state, provided the failure cause (load disconnected) has disappeared. in low current mode (csr1), ol_on is done periodically instead of continuously, and only operates when fast slew rate is selected. when the inte rnal pwm module is used with an internal or external clock (case 1), the period is 150 ms (typ.). when the direct inputs are used (case 2), the period is that of the input signal. the detection instants in both cases are given by the following: 1. in internal pwm (int./ext. clock) , low current mode (csr1) , openload in on state detection is not performed each switching period, but at a fixed frequency of about 7.0 hz (each t olled =150 ms typ.). the function is available for a duty cycle of 100%. olon detection is also performed at 7.0 hz, at the first turn-off event occurring 150 ms after the previous ol_on detection event (before os and ol_off). 2. in direct input , low current mode (csr1) , ol_on is performed each switching period (at the turn-off instant) but the duty cycle is restricted to the values. consequently, when the signal on the in[x] pin has a duty cycle of 100%, ol_on is not performed. to solve this problem, either the internal pwm function must be activated with a duty cycle of 100%, or the channel?s direct input must be disabled by setting dir_dis_s=1 (bit d5 of the confr-s regist er). the olon-bit is only reset when the faultr register is read after occurrence of an ol_on detection event without fault presence. openload detection in discontinuous conduction mode if small inductive loads (solenoids / dc motors) are driven at low frequencies, discont inuous conduction mode may occur. undesired openload in on state errors may then be detected, as the inductor current needs some time to rise above the openload detection threshold after turn-on. this problem can be solved by increasing the switching frequency, or by disabling the function and activating openload in off state detection instead. when small dc motors are driven in discontinuous conduction mode, undesired openload in off state detection may also occur when the load current reaches 0 a during the off state. this problem can be solved by increasing the switching frequency, or by enabling openload in the off state detection only during a limited time, preferably directly after turn-off (see diagnostic features ). the signal on the sync pin can be used to identify the turn-off instant. current & temperature sensing the scaled values of either of the output currents or the temperature of the device?s gnd pin (#14) can be made available at the csns pin. to monitor the current of a particular channel or the general device temperature, the csns0_en and csns1_en bits (see table 22 ) in the general configuration register (gcr) mu st be set to the appropriate values. when overcurrent windows are active, current sensing is disabled and the syncb pin remains high. instantaneous and sampled current sensing the device offers two possibilit ies for load current sensing: instantaneous (synchronous) sensing mode and track & hold mode (see figure 9 ). in synchronous mode, the load current is mirrored through the current sense pin ( output current monitoring (csns) ) and is therefore synchronous with it. after turn-off, the current se nse pin does not output the channel current. in track & hold mode however, the current sense pin continues to mirror the load current as it was just before turn-off. synchronous mode is activated by setting the t_h_en bit to 0, and track & hold mode by setting the t_h_en bit to 1. current sense ratio selection the load current is mirrored through the csns pin with a sense ratio ( figure 17 ) selected by the csns_ratio bit in the ocr register. to achieve optimal accuracy at low current levels, the lower current sensing ratio, called csr1, can be selected. in that case, the overcurrent threshold levels are decreased. the best accuracy that can be obtained for both ratios is shown in figure 18 . the amount of current the csns pin can sink is limited to i csns,max. .the csns pin must be connected to a pull-down resistor (470 ? < r(csns) <10 k ? , 1.0 k ? typical), in order to generate a voltage output. a small low-pass filter can be used for filtering out switching transients ( figure 21 ). current sensing operates for load currents up to the lower overcurrent threshold (oclx a). synchronous current sensing mode for activation of synchronous mode, t_h_en must be set to 0 (default). after turn- on, the csns output current accurately reflects the value of the channel?s load current after the required settling time. from this moment on (csns valid), the sync pin goes low and remain low until a switch off signal (internal/external) is received. this allows synchronization of the device?s current sensing feature with an external process running on a separate device (see current sense synchronization (sync) ). after turn-off, the load current does not flow through the switch, and the load current cannot be monitored. track & hold current sensing mode in track & hold mode (t&h) (t_h_en = 1), conversely from synchronous mode, the csns output current is available even after having switc hed off the load. this feature is useful when the device oper ates autonomously (internal clock/pwm), since it allows current monitoring without any synchronization of the device. an external sample and hold (s/h) capacitor is not requir ed. after turn on, the csns output current reflects the channel?s load current with the specified accuracy, after occurrence of the negative edge on the sync pin, as in synchronous mode (see current sense synchronization (sync) ). however, at the switch-off instant, the last observed csns current is sampled and its value saved, thanks to an internal s/h capacitor. the sync pin goes high (sync = 1). if the channel on which track & hold current sensing is performe d is changed to another, the free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 39 10XSD200 functional device operation operation and operating modes internal s/h hold capacitor is first emptied and then charged again to allow current monitoring of the other channel. consequently, t&h current monitoring of a channel is lost when this channel is in the off state at the moment the current is monitored on the other channel. track & hold mode should not be used for frequencies below 60 hz. . figure 17. current sensing ratio versus output current current sense errors current sense accuracy is adversely affected by errors of the internal circuitry?s current sense ratio and offset. the value of the current sensing out put current can be expressed with sufficient accuracy by the following equation: i csns = (i(hs[x])+ i _load_err_sys + i _load_err_rand )*c srx (1) with c sr0 = (1/3000+ ? gain0 ) and c sr1 = (1/1000+ ? gain1 ). the device?s offset error has a ?systematic? and a ?random? component (i _load_err_sys , i _load_err_rand ) . at low current levels, the random offset error may become dominant. the systematic offs et error is caused by predictable variations with supply voltage and temperature, and has a small but positive value with small spread. the random offset error is a rando mly distributed parameter with an average value of zero, but with high spread. the random offset error is subject to part to part variations and also depends on the values of supply voltage and device temperature. the device has a special feature called offset compensation, allowing an almost comp lete compensation of the random offset error (see e sr0_err ). this offset compensation technique greatly minimizes this error. computing the compensated current sensing value is illustrated in th e next sections. activation and use of offset compensation according to the settings of the ofp_s bit (in the retryr_s register), opposite va lues of the random offset error are generated. to compensa te the random offset error, two separate measurements with opposite values of the random offset error are require d. the measured values must be saved by an external micro-processor. compensation of the random offset error is achieved by computing the average of both. when a dedicated bit called offset positive (ofp = bit d8 of the retryr_s register) is set to 1, the current sunk through the csns pin (i csns ) can be described by: i csns1 =csr x *(i load + i _load_err_sys + i _load_err_rand )(2) when bit ofp is set to 0, i csns can be described by: i csns2 = csr x *(i load + i _load_err_sys - i _load_err_rand ) (3) the random offset term i _load_err_rand can be computed from equations (2) and (3) as follows: i _load_err_rand = (i csns1 - i csns2 ) / (2*csr x )(4) the compensated current sense value i csns,comp can be obtained by computing the average value of measurements i csns1 and i csns2 as follows: i csns, comp = (i csns1 + i csns2 ) / 2 (5) when equations 2 and 3 are substituted in equation 5, the random offset error cancels out, as shows eq. 6: i csns, comp = (i _load_err_sys + i load ) * csr x (6) the systematic offset error i _load_err_sys is referenced at the operating point 28 v and 25 c. it can eventually be fine tuned by performing a calibration. gain errors at 25 c (=current sense ratio errors, represented by ? gain0 and ? gain1 ) can also be reduced by performing a calibration at a point in the range of interest. if calib ration can not be done, it is recommended to use the typical value of i _load_err_sys (see systematic offset error (see current sense errors) ). current sense error model the figures of uncompensated and compensated current sense accuracy mentioned in table 3 , have been obtained by applying the error model of eq. 7 to the data: i csns_model = (i(hs[x])+ i _load_err_sys ) * c srx (7) e srx_err = (i csns1 - i csns_model )/i csns_model (8) e srx_err(comp) = (i csns, comp - i csns_model )/i csns_model (9) the computation has been applied to each of the specified measurement points. model parameters i _load_err_sys and c srx have the nominal values, specified on e sr0_err . the load current can be computed from this model as: i(hs[x]) = i csns / csr x - i _load_err_sys (uncompensated) (10) i(hs[x]) = i csns,comp / csr x - i _load_err_sys (compensated)(11) offset compensation in track & hold mode in track & hold mode, the last observed sense current (i csns ) is sampled at the switch off instant. this takes into account the currently active se ttings of the ofp_s offset compensation bit. changing the value of the ofp bit during the switch?s off time produces an identical value of the current sense output. consequently, to implement the before mentioned offset compensation technique, the channel must have been turned on at least once prior to sensing the output current, with an opposite value of the ofp bit. 0 500 1000 1500 2000 2500 3000 3500 4000 0246810 o u tp u t c u rre n t (a ) current sensing ratio 1/csr0 1/csr1 free datasheet http:///
analog integrated circuit device data ? 40 freescale semiconductor 10XSD200 functional device operation operation and operating modes system requirements for current monitoring current monitoring is usually implemented by reading the (rc-filtered) voltage across the pull-down resistor connected between the csns pin and gnd ( figure 21 ). therefore, measurements (1) and (2) must be spaced sufficiently wide apart (e.g. 5 time constants) to get stabilized values, but close enough to be sure that th e offset value wasn?t changed. the a/d converter of the external micro-controller that is used to read the current sense voltage v(csns) must have sufficient resolution to avoid introducing additional errors. accuracy with and without offset compensation the sensing accuracy for csr0 and csr1, obtained before and after offset compensation, is shown in figure 18 (solid lines = full scale accuracy with offset compensation and dotted lines without offset compensation). . figure 18. current sense accuracy versus output current in track & hold mode, the accuracy of the current sense function is lowered according to the values shown in figure 19 (error percentage as a function of the switch-off time is displayed, for csr0 and csr1). track & hold mode shouldn?t be used below f= 60 hz. figure 19. track and hold current sense accuracy temperature prewarning detection in normal mode, the temperature prewarning (otw) bit is set (faultr register) when the observed temperature of the gnd pin is higher than t otwar (pin #14, see figure 3 ). the feature is useful when the temperature of the direct surroundings of the device must be monitored. however, the channel isn?t switched off. to be able to reset the otw-bit, the faultr register must be read after the moment that temperature t c < t otwar . switching state monitoring the switching state (on/off) of the channels is reported in real time by bits out[x] in the statr register (bit od0/od1). the out[x] bit is asserted logic high when the channel is on (output voltage v(hs[x ]) higher than v pwr /2). when supply voltage v pwr drops below 13 v, the reported channel state may not correspond to the state of the channel?s control signal hson[x], in case of an open load fault (see factors determining the channel?s switching state ). emc performances specified emc performance is board and module dependent, and applies to a typical application ( figure 21 ). the device withstands transients per iso 7637-2 /24 v. an external freewheeling diode connected to at least one output is required for sustaining iso 7637 pulse 1 (600 v). to withstand pulse 2, at least one of the 2 channels must be connected to a typical load (bul b). it withstands electric fields up to 200 v/m and bulk current injection (bci) up to 200 ma per iso11452. the device meets class 5 of the cispr25 emission standard. 10XSD200 free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 41 10XSD200 functional device operation logic commands and spi registers logic commands and spi registers spi protocol description the spi interface offers full duplex, synchronous data transfer over four i/o lines: se rial input (si), serial output (so), serial clock (sclk), and chip select (csb).the si / so pins of the device follow a first-in first-out (d15 to d0) protocol. transfer of input an d output words starts with the most significant bit (msb). all inputs are compatible with 5.0 or 3.3 v cmos logic levels. parity check is performed after transfer of each 16-bit spi data word.the spi interface can be driven without series resi stors provided that voltage ratings on v dd and spi pins ( table 2 ) aren?t exceeded. unused spi-pins must be tied to gnd, eventually by resistors (see device ground loss ). figure 20. 16-bit spi interface timing diagram serial input communication protocol spi communication requires that rstb = high. spi communication is accomplis hed with 16-bit messages. a valid message must start with the msb (d15) and end with the lsb (d0) ( table 21 ). incoming messages are interpreted according to table 11 . the msb, d15, is the watchdog bit (wdin). bit d14, parity check (p ), must be set such that the total number of 1-bits in the spi word is even (p=0 for an even number of 1-bits and p=1 for an odd number). bank selection is done by setting bit d13. bits d12: d10 are used for register addressing. the remaining ten bits, d9 : d0, are used to configure the device and activate diagnostic and protective functions. multiple messages can be transmitted for applications with daisy chaining (or to validate already transmitted data) by keeping the csb pin at logic 0. messages with a length different fr om a multiple of 16 or with a parity error are ignored. th e device has thirteen input registers for device config uration and thirteen output registers containing the faul t/device status and settings. table 11 gives the si register function assignment. bit names with extension ?_s? refer to functions that have been implemented independently for each of both channels. serial port operation when chip select occurs (1-to-0 transition on the csb pin), the output register data is clocked out of the so pin (msb-first) at the serial clock frequency (slck). bits at the si pin are clocked in at the same time. the first sixteen so register bits are those addressed by the previous si word (bit d13, d2?d0 of the statr_s input register). at the end of the chip select event (0-to-1 transition), the si register contents are latched. the seco nd spi word clocked out of the serial output (so) after the first csb event represents the initial so register contents. this allows daisy chaining and data integrity verification. the message length is validat ed at the end of the csb event (0-to-1 transition). if it is valid (multiples of 16, no parity error), the data is latched into the selected register. after latch-in, the so pin is tri-stat ed and the status register is updated with the latest fa ult status information. daisy chain operation daisy-chaining propagates commands through devices connected in series. the comm ands enter the device at the si pin and leave it by the so pin, delayed by one command cycle of 16 bits. to address a particular device in a daisy chain, the csb pin of all the devices in that chain has to be kept low until the spi message has arrived at its destination. once the command has been clocked in by the addressed device, it can be executed by setting csb =1. 1. rstb must be in a logic [1] state during data transfer. 2. data enter the si pin starting with d15 (msb) and ending with bit d0. 3. data are available on the so pin starting with bit 0d15 (msb) and ending with bit 0 (od0). notes csb sclk si so d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 od15 od14 od13 od12 od11 od10 od9 od8 od7 od6 od5 od4 od3 od2 od1 od0 free datasheet http:///
analog integrated circuit device data ? 42 freescale semiconductor 10XSD200 functional device operation logic commands and spi registers table 10. si message bit assignment bit n si reg. bit bit functional description msb . . . . lsb d15 watchdog in (wdin): its state must be alter nated at least once within the timeout period d14 parity (p) check. p-bit must be set to 0 for an even number of 1-bits and to 1 for an odd number. d13 selection between si registers from bank 0 (0= channel 0) and bank 1 ( table 13 ). d12 : d10 register address bits. d9:d0 used to configure the device and the protective functions and to address the so registers. table 11. serial input register addresses and function assignment si register si data d 15 d 14 d 13 d 12 d 11 d 10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 statr_s wdin p a 0 0 0 0 0 0 0 0 0 0 0 soa2 soa1 soa0 pwmr_s wdin p a 0 0 0 1 0 on_s pwm7_s pwm6_s pwm5_s pwm4_ s pwm3_s pwm2_s pwm1_s pwm0_s confr_s wdin p a 0 0 1 0 0 os_dis_s olon_dis _s oloff_dis _s dir_dis_s sr1_s sr0_s delay2_s delay1_s delay0_ s ocr_s wdin p a 0 1 0 0 0 hocr_s pr_s clock_int_s csns_rati o_s t och_s tocm_s och_s ocm_s ocl_s retry_s wdin p a 0 1 0 1 0 ofp_s 0 0 0 0 auto_period 1_s auto_period 0_s retry_unli mited_s retry_s gcr wdin p 0 1 1 0 0 pwm_en _1 pwm_en_ 0 parallel t_h_en wd_dis v dd_fail_en csns1_en csns0_en ov_dis calr_s wdin p a 0 1 1 1 0 1 0 1 0 1 1 0 1 1 contents after reset* 0 x 0 x x x 0 0 0 0** 0 0 0 0 0 0 * = rstb = 0 or v dd (fail) after v dd = 5.0 v or por ** = except bit d6 (parallel) of the gcr register that is saved when v dd (fail) occurs, provided v dd = 5.0 v and v dd_fail_en = 1 before x = register address, p = parity bit free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 43 10XSD200 functional device operation logic commands and spi registers si register addressing the address in the title of the following sections (a 0 xxx) refer to bits d[13:10] of the spi word required to address the associated si register. bit a 0 = d13 selects between registers of bank 0 and bank 1 ( table 13 ). the function assignment of register bits d[8:0] is described in the associated section. the ?_s? behind a register name indicates that the variable applies to the register contents of both banks. address a 0 000 ? status register (statr_s) to read back the contents of any of the 13 so registers, bits d[13:10] of the channel?s si statr register must be set to a 0 000 and bits d[2:0] in the same spi word to the address of the desired so register. t he so registers thus addressed are: statr, faultr_s, pwmr_s, confr_s, ocr_s, retry_s, gcr, and diagr ( table 12 ). address a 0 001? pwm control register (pwmr_s ) the pwmr_s register conten ts determines the value of the pwm duty cycle at the output ( table 11 ), both for internal and external clock signals. bit d8 must be set to 1 to activate this function. the desired value of duty cycle is obtained by setting bits d7:d0 to one of the 256 levels as shown in table 6 .to start the table 12. serial output register bit assignment bits d13, d2, d1, d0 of the previous statr so returned data s o a 3 s o a 2 s o a 1 s o a 0 od 15 od 14 od 13 od 12 od 11 od 10 o d9 od8 od7 od6 od5 od4 od3 od2 od1 od0 statr 0 0 0 0 wdi n pf soa 3 soa 2 so a1 so a0 n m ov uv por r_ful l1 r_ful l0 fault1 fault0 out1 out0 fault r_s a 0 0 0 1 wdi n pf soa 3 soa 2 so a1 so a0 n m otw 0 0 olon _s oloff _s os_s ot_s sc_s oc_s pwmr_ s a 0 0 1 0 wdi n pf soa 3 soa 2 so a1 so a0 n m on_ s pwm 7_s pwm6 _s pwm5 _s pwm4 _s pwm3_s pwm2_s pwm1_s pwm0_s confr _s a 0 0 1 1 wdi n pf soa 3 soa 2 so a1 so a0 n m os_ dis_s olo n_di s_s oloff _dis_s dir_di s_s sr1_s sr0_s delay2_s delay1_ s delay0_ s ocr_s a 0 1 0 0 wdi n pf soa 3 soa 2 so a1 so a0 n m hoc r_s pr_s clock_i nt_s csns_ ratio_s toch_ s tocm_s och_s ocm_s ocl_s retry r_s a 0 1 0 1 wdi n pf soa 3 soa 2 so a1 so a0 n m ofp r3 r2 r1 r0 auto_period 1_s auto_period0 _s retry_unli mited_s retry_s gcr 0 1 1 0 wdi n pf soa 3 soa 2 so a1 so a0 n m pwm _en_ 1 pwm _en_ 0 paral llel t_h_e n wd_di s vdd_fail_e n csns1_en csns0_e n ov_dis diagr 0 1 1 1 wdi n pf soa 3 soa 2 so a1 so a0 n m con f1 con f0 id1 id0 in1 in0 clock_fail cal_fail1 cal_fail0 content s after reset or failure* n/ a n/ a n/ a n/ a 0 0 0 0 0 0 0 0 0 0** 0*** 0 0 0 0 0 * = rstb = 0 or v dd (fail) after v dd = 5.0 v, or por ** = except bit d6 (parallel) of the gcr register that is saved when v dd (fail) occurs provided v dd = 5.0 v and vdd_fail_en = 1 before *** = except bit d7 (por) of the statr register that is saved when v dd (fail) occurs after v dd = 5.0 v and vdd_fail_en = 1 (fail-safe mode) x = register address, pf = parity fault table 13. value of bit a 0 required for addressing register banks 0 or 1 value a 0 (d13) bank 0 0 = channel 0 (default) 1 1 = channel 1 free datasheet http:///
analog integrated circuit device data ? 44 freescale semiconductor 10XSD200 functional device operation logic commands and spi registers pwm function at a known point in time, the pwm_en_s bit (both in the gcr register) must be set to 1. address a 0 010? channel configuration register (confr_s ) the confr_s is used to select the appropriate value of slew rate and turn-on delay. the settings of bits d[8:6] determine the activation of openload and short-circuit (to v pwr ) detection. bit d13 ( = a 0 ) of the incoming spi word determines which of both confr registers is addressed ( table 10 ). setting bit d8 (os_dis_s) to logic [1] disables detection of short-circuits between the ch annel?s output pin and the vpwr pin. the default value [0] enables the feature. setting bit d7 (olon_dis_s) to logic [1] disables detection of openload in the on state fo r the selected channel. the default value [0] enables this feature ( table 14 ). setting bit d6 (oloff_dis_s) to logic [1] disables detection of openload in the of f state. the default value [0] enables the feature, see table 14 . setting bit d5 (dir_dis_s) to logic [0] enables direct control on the selected channel. setting bit d5 to logic [1] disables direct control. in t hat case, the channel state is determined by the settings of the internal pwm functions. d4:d3 bits (sr1_s and sr0_s) control the slew rate at switch on and switch off ( table 15 ). the default value ([00]) corresponds to the medium slew rate. rising and falling edge slew rates are identical. delaying a channel?s turn-on instant with respect to the other is accomplished by setting bits d2 : d0 of the pwmr_s register to the appropriate va lues. switch on is delayed by the number of (internal/externa l) clock periods shown in table 7 . refer to the section programmable pwm module . address a 0 100 ? overcurrent protection configuration re gister (ocr_s) the contents of the ocr_s r egisters determines operation of overcurrent, current sensing, and pwm related functions. for each load type (bulb or dc motor), a different kind of overcurrent profile exists (see figure 5 ). for lighting mode, the overcurrent profile is defined by three different thresholds called the higher (=i _och ), the middle (=i _ocm ) and the lower (=i _ocl ) threshold. the dc motor profile only has two thresholds (i _och and i _ocl ). each threshold can have 2 different values, except i _ocl that can have 3 different values (i _ocl1 , i _ocl2 , i _ocl3). setting the low current sense ratio (csr1) reduces the values of all the overcurrent thresholds by a factor of three. the terminology is defined as follows: i _ocxy_z stands for overcurrent threshold x (x=h, m or l) that can have two or three different values, selected by y (y=1, 2, (or 3)). the previously selected current se nse ratio (z=0 for csr0 and z=1 for csr1) further determines the value of the applicable overcurrent threshold, see: overcurrent detection thresholds with csns_ratio bit = 0 (csr0) . setting bit d8 (hocr_s) to 0 acti vates overcurrent level i _ocl1 , the highest of the 3 levels, regardless the value of the d0 bit. setting hocr to 1 activates the medium level i _ocl2 when d0 = 0, and the lowest level i _ocl3 when d0 = 1 ( table 20 ). when overcurrent windows are active, current sensing is not available. bit d7 (pr_s) controls which of two divider values are used to create the pwm frequency from the external clock. setting bit d7 to 1 causes the external clock to be divided by 512. when pr_s = 0, the divider is 256. setting bit d6 (clock_int_s) activate s the internal clock of the selected channel. the default value [0] configures the pwm module to use an external clock signal. setting bit d5 (csns_ratio_s) to 1 activates the ?low- current? current sense ratio csr1, optimal for measuring currents in the lowest range. the default value [0] activates the ?high-current? sensing ratio csr0 ( table 16 ). the width of the overcurrent protection window(s) is controlled by bits d4 and d3 (t och_s and t ocm_s ), and also depends on the load type configuration as shown in table 17 . (conf[x]=0: bulb lamp, conf[x]=1: dc motor). the lighting profile has two adjacent windows the width of which is compatible with typical bulb inrush current profiles. the width of the first of these windows is either t och1 or t och2 . the width of the second window is either t ocm1_l or t ocm2_l (see table 17 ). table 14. selection of openload detection features olon_dis_s (d7) (in on state) oloff_dis_s (d6) (in off state) selected openload detection function 0 0 both enabled (default) 0 1 off state detection disabled 1 0 on state detection disabled 1 1 both disabled table 15. slew rate selection sr1_s (d4) sr0_s (d3) slew rate 0 0 medium (default) 0 1 low 1 0 high 1 1 medium sr analog integrated circuit device data ? freescale semiconductor 45 10XSD200 functional device operation logic commands and spi registers the dc motor profile has only one overcurrent window defined by only two different thresholds (i _och and i _ocl) as illustrated by figure 6 . in this case, the maximum overcurrent duration is selected among four values: t ocm1_m , t ocm2_m , t och1 and t och2 . bit d2 (och_s) selects the value of the higher (upper) overcurrent threshold among two values. the default value [0] corresponds to the highest value, and [1] to the lowest value ( table 18 ). bit d1 (ocm_s) sets the value of the middle overcurrent threshold. the default value [0] corresponds to the highest value, and [1] to the lowest value ( table 19 ). in dc motor mode, there is no middle overcurrent threshold and the value of this bit has no influence. bit d0 (ocl_s) and d8 (hocr) set the value of the lowest overcurrent threshold accordingly, as shown in table 20 . address a 0 101 ? auto-retry register (retryr_s) the retryr_s register contents are used to configure the different auto-retry options ( auto-retry ) and the offset compensation feature of the current sense function. setting bit d8 to 1 (ofp = 1) causes the offset current to be added to the sensed current (csns). setting bit d8 to 0 results in the offset current be ing subtracted from the sensed current. setting d3 and d2 ( table 21 ) to the appropriate values allows selection of the value of the auto-retry period among four predefined values. setting bit d1 to 1 (retry_unlimited_s = 1) results in an unlimited number of auto retr ies, provided the auto-retry function wasn?t disabled. setting bit d1 to 0 (retry_unlimited_s = 0) limits the amount of auto retries to 16 (see number of auto-retries ). the value of the counter is neit her reset after delatching, nor when the fault disappears. setting bit d0 (retry_s) enables or disable auto-retry, accordingly to setting of the conf pin. for conf[x] = 0 (lighting profile configured), setting retry_s = 1 disables auto-retry. the default value [0] enables it. for conf[x] = 1 (dc motor), setting retry_s = 1 enables auto-retry. the default value [0] disables it. table 17. dynamic overcurrent threshold activation times for bulb an d dc motor profiles conf[x] t och_s (d4) t ocm_s (d3) selected threshold activation times 0 0 0 t och1 and t ocm1_l 0 0 1 t och1 and t ocm2_l 0 1 0 t och2 and t ocm1_l 0 1 1 t och2 and t ocm2_l 1 0 0 t ocm1_m 1 0 1 t ocm2_m 1 1 0 t och1 1 1 1 t och2 table 18. och upper current threshold selection och_s (d2) och current threshold 0 och1_s (default) 1 och2_s table 19. ocm current threshold selection ocm_s (d1) ocm current threshold 0 ocm1_s (default) 1 ocm2_s table 20. ocl current threshold selection hocr (d8) ocl_s (bit d0) selected ocl current level 0 0 ocl1_x (default) 0 1 ocl1_x 1 0 ocl2_x 1 1 ocl3_x table 21. auto-retry period auto_period1_s (d3) auto_period0_s (d2) retry period 0 0 t auto_00 (default) 0 1 t auto_01 1 0 t auto_10 1 1 t auto_11 free datasheet http:///
analog integrated circuit device data ? 46 freescale semiconductor 10XSD200 functional device operation logic commands and spi registers address 0110 ? global configuration register (gcr) the gcr register is used to activate various functions and diagnostic functions.see table 10 setting bits d8 = 1 and d7 = 1 of the gcr register (pwm_en_1 and pwm_en_0) activates the internal pwm function of both channels simultaneously according to the values of duty cycle and turn-on delays in the pwmr_s and confr_s registers ( table 6 ). however, this option should never be used to drive channels in parallel. to increase the load current capability, the instructions in the section parallel operation should be followed. setting bit d6 sets parallel mode (improved switching synchronization between both channels). only configuration and diagnostic information of bank 0 (a 0 = 0) is available in this setting (see parallel operation ). setting bit d5 (t_h_en = 1) activates track & hold current sensing mode. when t&h is ac tivated, the value of the channel?s load current is kept available after turn-off. setting bit d4 (wd_dis = 1) disables the spi watchdog function. a logic [0] enables the spi watchdog. setting bit d3 (v dd_fail_en = 1) enables or disables the v dd failure detection. when enabled, the device enters fail- safe mode after v dd < v dd(fail). bits d6 (parallel bit), d2 and d1 set the different (current) sensing options. the csns pin outputs a scaled value of the selected channel?s load current, the sum of both currents or the die temperature, according to the values in table 22 . when the highest overcurrent rang e is selected (bit d8 of the ocr register, hocr = 0), the device?s csns pin outputs scaled values of a single channel?s load current. setting bit d0 (ov_dis = 1 of the gcr reg.) disables overvoltage protection. setting this bit to [0] (default), enables it. address a 0 111 ? calibration register (calr_s) the internal clock frequency of both channels can be calibrated independently. setting the appropriate calibration word in the calr_s register ( table 11 ) puts the device in calibration mode. the default switching frequency is 400 hz, but can be changed by applying a specific calibration procedure. see internal clock & internal pwm (clock_int_s bit = 1) . so register addressing the device has two register banks, each of which has five channel-specific so register s containing the channel?s configuration and diagnostics status ( table 12 ). these registers are faultr_s, pwmr_s, confr_s, ocr_s, and retryr_s. global fault and diagnostic information are contained in the following common so-reg isters: statr, gcr, and diagr. all the so registers can be addressed by setting the appropriate bits in the si-sta tr_s register (bits d13, d2, d1, d0). the value of the bit d13 determines which register bank is addressed (bank 0 or 1). data is made available the next cycle after register addressing. the output status register corr ectly reflects the contents of the addressed so register as long as csb is low, except when the data from the previous spi cycle was invalid. in this case, the device outputs the cont ents of the last successfully addressed so register. serial output register assignment the output register that are shifted out through the so pin is previously addressed by bits d13, d2, d1, and d0 of the statr_s si register ( table 11 ). table 12 gives the functional assignment (od15 : od0) of each of the thirteen so register bits, preceded by the address of the si statr_s required to address it. ? bit od15 (msb) reports t he state of the watchdog bit from the previously clocked-in spi message. ? bit od14 (pf, active 1) repo rts an eventual parity error on the previously transferred si register contents. ? bits od13:od10 echo the stat e of bits d13, d2, d1, and d0 (soa3: soa0) of the previously received si word. ? bit od9: normal mode (nm) reports the device state. in normal mode, nm = 1. ? bits od8 : od0 are the contents of the selected so register (addressed by bit d13 and bits d2 : d0 of the previous si statr register). table 22. current sense pin functionality selection d8 d6 d2 d1 activated function at csns pin x x 0 0 disabled 0 x 0 1 current sensing on channel 0 0 x 1 0 current sensing on channel 1 0 x 1 1 temperature sensing 1 0 0 1 current sensing on channel 0 1 x 1 0 current sensing on channel 1 1 x 1 1 temperature 1 1 0 1 sensing of summed currents; channels 0 and 1 free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 47 10XSD200 functional device operation logic commands and spi registers previous address soa 3 : soa 0 = 0000 (statr) when bits soa3?soa0 of th e previously received si statr_s register = 0000, the so statr register is addressed. bits od8: od0 contain the relevant channel information: faults, channel state, and supply voltage errors. ?bits od8: od6 report failures common to both channels ?bit od8 = ov = 1: overvoltage fault ?bit od7 = uv = 1: undervoltage fault ?bit od6 = por = 1: power-on reset (por) has occurred power-on-reset occurs when v pwr t otwar ). reading either fault register clears both otw bits. bits od5: od0 of the fault register (faultr_s) report the faults that occurred on the channel previously selected by bit soa3 = a 0 ( table 13 ). ?bit od0 = oc_s: overcurrent fault on channel s, ?bit od1 = sc_s: severe short-circuit on channel s, ?bit od3 = os_s: output shorted to v pwr on channel s, ?bit od4 = oloff_s: openload in off state on channel s, ?bit od5 = olon_s: openload in on state on channel s. (the threshold value above which this fault is triggered depends on the selected current sense ratio; for csr0 @ 300 ma typ. and for csr1 @ 7.0 ma typ.). the fault status pin ( fsb) is set to 0 (active low) upon occurrence of any of the a bove mentioned faults. latched faults can only be delatched by the procedure described in fault delatching . the faultr_s register is reset when it is read out, provided that the failure cause has disappeared and latched faults have been delatched. previous address soa 3 : soa 0 = a 0 010 (pwmr_s) the device outputs the contents of the addressed pwmr_s register (a 0 = 0 for bank 0 and a 0 = 1 for bank 1). previous address soa 3 : soa 0 = a 0 011 (confr_s) the device outputs the contents of the addressed confr_s register (a 0 = 0 for bank 0 and a 0 = 1 for bank 1). previous address soa 3 : soa 0 = a 0 100 (ocr_s) the device outputs the content s of the addressed ocr_s register (a 0 = 0 for bank 0 and a 0 = 1 for bank 1). previous address soa 3 : soa 0 = a 0 101 (retryr_s) the device outputs the contents of the addressed retryr_s register (a 0 = 0 for bank 0 and a 0 = 1 for bank 1). bit od8 contains the value of the ofp bit (offset positive), used for current sense offs et compensation. bits od7: od4 contain the real time value of the auto-retry counter. when these bits contain [0000], ei ther auto-retry has not been enabled or auto-retry did not occur. previous address soa 3 : soa 0 = 0110 (gcr) the device outputs the contents of the general configuration register (gcr) common to both channels. previous address soa 3 : soa 0 = 0111 (diagr_s) bit od8 ( ch. 1 = conf1) and bit od7 ( ch. 0 = conf0) of the diagr_s register contai n the values of the channels? configuration bits (0 = bulb, 1 = dc motor) bits od6:od5 contain the pr oduct identification (id) number, equal to 00 for the present dual 10 m ? product. bits od4:od3 report the logic state of the direct inputs in[1:0] in real time (1 = on, 0 = off), od4 = ch. 1, od3 = ch. 0. bit od2 reports a logic [1] in case an external clock error occurred (if an external clo ck was selected by clock_int = 0) bit od1:od0 report logic [1] in case a calibration failure occurred during calibration of a channel?s internal clock period. free datasheet http:///
analog integrated circuit device data ? 48 freescale semiconductor 10XSD200 typical applications typical applications figure 21 shows the electrical circuit of a typical industrial application. as an example, an external circuit is added that takes over load control in case fail-safe mode is activated (fsob goes low). this circuit allows keeping full control of both channels in case of spi failure. figure 21. typical application with two different load types v dd v dd gnd mcu voltage regulator v pwr hs0 hs1 vpwr vdd clock fsb in0 sclk csb si so rstb in1 100 nf i/o i/o sclk csb si so 1.0 k 1.0 k 1.0 k 1.0 k 1.0 k load 0 load 1 csns a/d v dd vdd v pwr v dd 22 nf 22 nf 1.0 k external control circuitry v pwr 10 f 100 nf 10 f 100 nf 10 k 10 k fsob 10 k v pwr 100 k m conf1 conf0 direct controls gnd sync i/o i/o 22 nf 1.0 k 10 k 10XSD200 1.0 k 1.0 k <5.0 k 75 k 100 nf 1.0 f 1.0 k 470 pf 470 pf speed-up capacitor for spi frequencies > 4.0 mhz recommended on pins cs, sclk, si, so free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 49 10XSD200 typical applications . figure 22. two channels in parallel / recommended external current sense circuit v dd gnd mcu hs0 hs1 vpwr vdd clock fsb in0 sclk csb si so rstb in1 100 nf i/o i/o sclk cs si so 1.0 k 1.0 k 1.0 k 1.9 k load csns a/d v dd vdd v pwr v dd 22 nf 22 nf 1.0 k vpwr 100 nf 10 k fsob 10 k v pwr 100 k m conf1 conf0 direct controls gnd sync i/o i/o 1.0 k 10 k 10XSD200 1.0 k 1.0 k 75 k 75 k 1.0 k 1.0 ?f 470 pf 470 pf speed-up capacitor for spi frequencies > 4.0 mhz recommended on pins cs, sclk, si, so 1.0 k external control circuitry v dd voltage regulator v pwr 10 f 100 nf 10 f 100 nf free datasheet http:///
analog integrated circuit device data ? 50 freescale semiconductor 10XSD200 packaging soldering information packaging soldering information the 10XSD200 is packaged in a surface mount power package (pqfn), intended to be soldered directly on the printed circuit board. the an2467 provides guidelines for printed circuit board design and assembly. free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 51 10XSD200 packaging package dimensions package dimensions for the most current package revision, visit www.freescale.com and perform a keyword search using the 98asa00428d listed below. dimensions shown are pr ovided for reference only. fk suffix 23-pin pqfn 98asa00428d issue a free datasheet http:///
analog integrated circuit device data ? 52 freescale semiconductor 10XSD200 packaging package dimensions fk suffix 23-pin pqfn 98asa00428d issue a free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 53 10XSD200 packaging package dimensions fk suffix 23-pin pqfn 98asa00428d issue a free datasheet http:///
analog integrated circuit device data ? 54 freescale semiconductor 10XSD200 packaging package dimensions fk suffix 23-pin pqfn 98asa00428d issue a free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 55 10XSD200 packaging package dimensions fk suffix 23-pin pqfn 98asa00428d issue a free datasheet http:///
analog integrated circuit device data ? 56 freescale semiconductor 10XSD200 packaging package dimensions fk suffix 23-pin pqfn 98asa00428d issue a free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 57 10XSD200 packaging package dimensions fk suffix 23-pin pqfn 98asa00428d issue a free datasheet http:///
analog integrated circuit device data ? 58 freescale semiconductor 10XSD200 packaging package dimensions fk suffix 23-pin pqfn 98asa00428d issue a free datasheet http:///
analog integrated circuit device data ? freescale semiconductor 59 10XSD200 revision history package dimensions revision history revision date description of changes 1.0 7/2013 ? initial release based on the mc10xs4200 data sheet 2.0 9/2013 ? added note for operating temperature (8) free datasheet http:///
document number: mc10XSD200 rev. 2.0 9/2013 information in this document is provided solely to enable sys tem and software implementers to use freescale products. there are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based on the information in this document. freescale reserves the right to make changes without fu rther notice to any products herein. freescale makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. ?typical? parameters that may be provided in freescale data sheets and/or s pecifications can and do vary in diff erent applications, and actual performance may vary over time. all operating parameters, including ?typicals,? must be validated for each customer application by customer?s technical experts. freescale does not convey any license under its patent rights nor the rights of others. freescale sells products pursuant to standard terms and conditi ons of sale, which can be found at the following address: freescale.com/salestermsandconditions . freescale and the freescale logo, are trademarks of freescale semiconductor, inc., reg. u.s. pat. & tm. off. smartmos is a trademark of freescale semiconductor, inc. a ll other product or service names are the property of their respective owners. ? 2013 freescale semiconductor, inc. how to reach us: home page: freescale.com web support: freescale.com/support free datasheet http:///

▲Up To Search▲

Price & Availability of 10XSD200

	To Download 10XSD200 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .